MCSA Networking with Windows Server 2016?(updated) Skills Based Final Exam 100% correct

MCSA Networking with Windows Server 2016?(updated) Skills Based Final Exam 100% correctIn a software-defined networking environment, what network plane would be responsible for the ability to configure SNMP for remote monitoring? -data plane -management plane -control plane -behavior plane management plane What feature is utilized by the Windows Deployment Services (WDS) in conjunction with DHCP in order to deploy and install the Windows OS remotely via a network environment built into the target device's network card? -Unified Extensible Firmware Interface (UEFI) -Bootstrap Protocol (BOOTP) -Live Windows Installation Environment (LWIE) -Preboot Execution Environment (PXE) Preboot Execution Environment (PXE) What PowerShell command can you use to view all commands specific to BGP? -Display-Command *-BGP* -Get-Command *-BGP* -Apropos "BGP" -Show-Commands *BGP* Get-Command *-BGP* What does the "Over" value indicate when present in the "Utilization" field for a particular address block? -The block is using 100% of all available IP addresses in the block. -The block is over the specified utilization threshold, which is 50% by default. -The block is over the specified utilization threshold, which is 60% by default. -The block is over the specified utilization threshold, which is 80% by default. The block is over the specified utilization threshold, which is 80% by default. What two commands can be utilized in order to add a static route to the network 172.20.1.0/24 via the 10.0.5.1 gateway? -route net create 172.20.1.0 subnet 255.255.255.0 10.0.5.1 -route add 172.20.1.0 mask 255.255.255.0 10.0.5.1 -New-NetRoute -DestinationPrefix 172.20.1.0/24 -InterfaceAlias "Ethernet" -NexHop 10.0.5.1 -New-StaticRoute -Destination 172.20.1.0/24 -Iface "Ethernet" -Gateway 10.0.5.1 -route add 172.20.1.0 mask 255.255.255.0 10.0.5.1 -New-NetRoute -DestinationPrefix 172.20.1.0/24 -InterfaceAlias "Ethernet" -NexHop 10.0.5.1 What two PowerShell commands can be used to add forwarders to a DNS server's forwarders list, or change the settings of an existing forwarder, respectively? (Choose two.) -Add-DnsServerForwarder -Create-DnsServerForwarder -Set-DnsServerForwarder -Change-DnsServerForwarder -Add-DnsServerForwarder -Set-DnsServerForwarder What NPS template type specifies reusable RADIUS server settings? -Shared Secrets -RADIUS Clients -IP Filters -Remote RADIUS Servers Remote RADIUS Servers In a site-to-site VPN configuration, where is traffic encrypted? -Between client devices and the router/VPN servers. -Between client devices on both networks. -Between the router/VPN servers only. -Between client devices, the VPN servers, and external servers on the Internet. Between the router/VPN servers only. Dynamic routing for IPv4 is supported on Windows Server 2012/R2 by using what specific protocol? -RIPv2 -EIGRP -ISIS -OSPF RIPv2 IPv6 addresses can be shortened under specific conditions. What address is valid and can't be further shortened by using additional IPv6 formatting rules? -fe80::18ff:24:8e5a:60 -fe80::18ff:24:8e5a:0006 -fe80:0:0:0:18ff:24::8e5a:60 -fe80::18ff::24:8e5a:60 fe80::18ff:24:8e5a:60 You are migrating the IPAM service from Windows Server 2012 to Windows Server 2016, and you have just started the WID service on the new IPAM server after moving the database. What command must you use in order to utilize the database? -Update-IpamServer -Migrate-IpamServer -Update-WIDSchema -db ipam -Upgrade-IpamServer Update-IpamServer When using Hyper-V Network Virtualization (HNV), what is assigned to each virtual network within a datacenter for identification purposes? -Distributed Domain Identifier (DDI) -Routing Domain ID (RDID) -Virtual Network Unique ID (VNUID) -Virtual Subnet ID (VSID) Routing Domain ID (RDID) You are troubleshooting a server that appears to have a corrupted C file, and are attempting to copy the file from another working server. Where is this file located? -%systemroot%System32 DriversDNS -%systemroot%System32 DNS -%systemroot%DNS SettingsCache -%systemroot%System DNS %systemroot%System32DNS What command can be used to create a DNS zone policy named SeattlePol for a zone named MCSA that allows load balancing queries for this zone's records with the records from a scope named LAZScope (as an additional requirement, records should be returned from the SeattleZScope 3 times for every 1 time from the LAZScope)? -Add-DnsServerQueryResolutionPolicy -Name SeattlePol -ZoneName MCSA -Action Allow -ClientSubnet "eq,Seattle" -ZoneScope "SeattleZScope,3;LAZScope,1" -LoadBalance $true -Add-DnsServerQueryResolutionPolicy -Name SeattlePol -ZoneName MCSA -Action Allow -ClientSubnet "eq,Seattle" -ZoneScope "SeattleZScope,4;LAZScope,1" -Add-DnsServerQueryResolutionPolicy -Name MCSA -ZoneName SeattlePol -Action Allow -ClientSubnet "eq,Seattle" -ZoneScope 3:1 -Add-DnsServerQueryResolutionPolicy -Name SeattlePol -ZoneName MCSA -Action Allow -ClientSubnet "eq,Seattle" -ZoneScope "SeattleZScope,3;LAZScope,1" Add-DnsServerQueryResolutionPolicy -Name SeattlePol -ZoneName MCSA -Action Allow -ClientSubnet "eq,Seattle" -ZoneScope "SeattleZScope,3;LAZScope,1" If you are using a hosted cache mode BranchCache server, how is the trust established between BranchCache clients? -The trust is established at the domain controller level for the network. -The trust is established via an automatically generated DSA key. -The trust is established via a pre-shared key configured by the administrator. -The trust is established via the use of certificates. The trust is established via the use of certificates. What is the maximum number of identical physical adapters that can be configured as a team and mapped to a Switch Embedded Team (SET)? -eight -two -sixteen -four eight The use of DHCP name protection involves the creation of what type of resource record in order to verify that a name being registered in DNS is from the original computer that registered it? -Automatic Host Identification Record (AHIR) -Dynamic Host Configuration Identifier (DHCID) -Globally Unique Resource Record (GURR) -Dynmaic Resource Identification (DRID) Dynamic Host Configuration Identifier (DHCID) Where must you go in IPAM in order to create a new DHCP scope? -Click Monitor and Manage, then DNS and DHCP servers. Right click a server running DHCP, and left click "Create DHCP Scope" -Click Monitor and Manage, then DHCP servers. Click "Manage" next to the desired server. Click "Create scope". -Click Monitor and Manage, then DHCP servers. Click on the "Add a scope" button. -Click Monitor and Manage, then DNS and DHCP servers. Right click a server running DHCP, and left click "New DHCP Scope" Click Monitor and Manage, then DNS and DHCP servers. Right click a server running DHCP, and left click "Create DHCP Scope" By default, each tunneling type is enabled in the RRAS service when you configure a VPN. How many connections are allowed for each tunnel type? -256 -128 -32 -64 128 What statement regarding the use of Virtual Machine Queue (VMQ) is NOT accurate? -VMQ improves performance by delivering packets from an external network directly to the vNIC. -VMQ is a required feature in order to utilize virtual receive side scaling (vRSS). -VMQ places packets in a common queue and distributes them to destination vNICs on a first-come-first-served basis. -VMQ is limited to use on 10 Gbps or higher network adapters. VMQ places packets in a common queue and distributes them to destination vNICs on a first-come-first-served basis. What Software Load Balancer component is responsible for mapping VIPs to DIPs on incoming East-West traffic and forwards the traffic to the selected DIP? -SLB MUX -SLB Director -Network Controller -SLB Host Agent SLB MUX What is not a DNS server management task that can be completed via the IPAM management of DNS? -Clear a DNS server's cached lookups -Create a DNS zone -Launch the DNS MMC for a selected server -Create a conditional forwarder Clear a DNS server's cached lookups What is NOT a feature of Windows Server 2016's Datacenter Firewall? -Scalable software-based firewall that can be offered to multitenant virtual networks. -Operating system independent protection of VMs. -Flexible protection of VMs that allows for VMs to be moved among Hyper-V hosts without reconfiguring the firewall. -Supplemental hardware support, allowing firewall functions to be offloaded to dedicated firewall hardware. Supplemental hardware support, allowing firewall functions to be offloaded to dedicated firewall hardware. What are the two different primary types of DNS policy that can be applied with Windows Server 2016? -recursive query policy -query resolution policy -zone transfer policy -delegation policy -query resolution policy -zone transfer policy What PowerShell command can be used to activate a new DHCP scope? -Start-DhcpServer4Scope -State Enabled -Set-DhcpServer4Scope -State Enabled -Set-DhcpServer4Scope -State Active -Start-DhcpServer4Scope -State Active Set-DhcpServer4Scope -State Active What two commands could be utilized in order to enable the use of EUI-64 compliant IPv6 addresses on Ethernet ports in Windows Server 2008 or later? -netsh interface ipv6 set global eui-64=enabled -netsh interface ipv6 set global randomizeidentifiers=disabled -Set-NetIPv6Protocol -EUI64Identifiers Enabled -Set-NetIPv6Protocol -RandomizeIdentifiers Disabled -netsh interface ipv6 set global randomizeidentifiers=disabled -Set-NetIPv6Protocol -RandomizeIdentifiers Disabled While investigating a network issue, you discover your server has two routes to the same network that is having issues communicating with the server. The first route has a metric of 200, and the second route has a metric of 400. How does Windows handle traffic to the target network? -The traffic is load balanced between the two routes. -The default route is used instead of the specific routes. -The route with lower metric takes precedence. -The route with higher metric takes precedence. The route with lower metric takes precedence. You have created a new SET team and wish to enable the use of remote direct memory access (RDMA) on a virtual network adapter named "vEthernet (Adapter1)". What command do you use to do this? -Enable-NetRDMA -Interface "vEthernet (Adapter1)" -Set-VnetAdapter -RDMA $true -Iface "vEthernet (Adapter1)" -Set-AdapterProperties -Interface "vEthernet (Adapter1)" -EnableRDMA yes -Enable-NetAdapterRDMA "vEthernet (Adapter1)" Enable-NetAdapterRDMA "vEthernet (Adapter1)" What is used to define which IPAM objects an administrative role can access? -Role filter -Role based policy -Mandatory access control -Access scope Access scope After enabling the DHCP audit logging feature, where can you find the DHCP log? -C:WindowsSystem32dhcp -C:WindowsServicesdhcp -C:WindowsSystem32Logs -C:WindowsSystemdhcp C:WindowsSystem32dhcp The Network Policy Server (NPS) supports exporting templates to what file format? -XML -YAML -TXT -HTML XML What VPN tunnel type supports the use of the VPN reconnnect feature for Windows 7 and newer clients? -SSL -L2TP/IPsec -IKEv2 -SSTP IKEv2 In the context of the Windows Server RAS Gateway, what does it mean to be multitenant aware? -Tenants that use overlapping IP address space can use the same gateway. -Tenants that share the same host can communicate directly with each other. -Tenants that share the same host can utilize the same physical network resources. -Tenants that have conflicting IP address space are automatically reconfigured. Tenants that use overlapping IP address space can use the same gateway. Under what circumstances is it advisable to set the recursion timeout value and retry intervals higher than usual? -The settings are Microsoft recommended best practices for an increased security DNS server. -The settings should be used when a server is using DNSSEC to ensure a response. -The settings are advised when a server utilizes multiple local IP addresses. -The settings should be used when the server must use recursive queries over a slow WAN link. The settings should be used when the server must use recursive queries over a slow WAN link. In regards to the use of a superscope for DHCP, what statements are accurate? (Choose two.) -A supescope is a type of scope consisting of multiple combined IPv6 prefixes. -A superscope is used to combine the address pools within multiple scopes. -Deactivation of a superscope deactivates the member scopes as well. -A superscope has unique DHCP options not present in member scopes. -A superscope is used to combine the address pools within multiple scopes. -Deactivation of a superscope deactivates the member scopes as well. In a software-defined networking environment, what network plane determines how the device operates and how it learns about its network environment? -behavior plane -management plane -control plane -data plane control plane At present, what are the two binary bit patterns that an IPv6 address must begin with in order to make it a valid global unicast address? (Choose two.) -0001 -0010 -0011 -0101 -0010 -0011 You are attempting to provision IPAM utilizing Active Directory Group Policy, and have configured a GPO name prefix of IPAMmcsa. What policy should you use to set the firewall rules and other policies needed for the IPAM server to collect data from domain controllers and NPS servers? -IPAMmcsa_Fw_Pol -IPAMmcsa_Fw_NPS -IPAMmcsa_DC_Sec -IPAMmcsa_DC_NPS IPAMmcsa_DC_NPS