Page 1 of 143
Arizona CR-7 Carpentry Contractor Exam Practice
Exam QUESTIONS AND VERIFIED ANSWERS WITH
RATIONALES JUST RELEASED
Arizona CR-7 Carpentry Contractor Exam Practice Questions
EXAM COVERAGE — 10 MOST-TESTED AREAS
1. Rough Carpentry and Structural Framing — Wall framing, floor framing, roof framing, studs,
plates, joists, rafters, beams, headers, blocking, bracing, layout, fastening, and structural
connections.
2. Finish Carpentry and Millwork — Interior trim, baseboards, casing, crown molding, cabinets,
countertops, paneling, stair trim, wood flooring, scribing, fitting, and finish quality.
3. Doors, Windows, and Hardware — Door installation, frames, hinges, locks, closers, window
installation, shimming, flashing, weatherproofing, alignment, and operation.
4. Plans, Measurements, Layout, and Calculations — Reading construction drawings, dimensions,
scales, square footage, linear measurements, material quantities, angles, elevations, and layout
procedures.
5. Wood Materials and Fasteners — Lumber grades, engineered wood, plywood, OSB, treated
lumber, nails, screws, bolts, anchors, adhesives, connectors, and selecting materials for the
application.
6. Roof and Floor Systems — Roof framing, trusses, rafters, sheathing, roof openings, floor joists,
subflooring, decking, blocking, and proper load transfer.
7. Exterior Carpentry and Weather Protection — Siding, exterior trim, flashing, moisture control,
caulking, window and door weatherproofing, decks, exterior wood protection, and drainage.
8. Metal Studs and Metal Door/Frame Work — Light-gauge metal framing, tracks, studs,
fastening, openings, door frames, alignment, reinforcement, and installation practices.
9. Safety, Tools, and Work Practices — Hand and power tools, ladders, scaffolds, PPE, fall
protection, electrical safety, housekeeping, material handling, and job-site hazards.
10. Arizona Contractor Responsibilities and Business Rules — CR-7 scope, qualifying-party
responsibilities, subcontracting work outside the classification, licensing, contracts, permits,
inspections, workmanship, and Arizona ROC requirements. (Arizona Registrar of Contractors)
1.
, Page 2 of 143
A carpenter is laying out a new wall before installing the studs. What should be checked first to keep the
wall correctly positioned?
A. Paint color
B. Wall dimensions and reference lines
C. Door hardware
D. Cabinet finish
Answer: B
Rationale: Wall dimensions and reference lines establish the correct location and size before studs are
installed.
2.
A floor joist must carry a load across an opening. Which condition is most important when selecting the
proper joist size?
A. Wall paint color
B. Span and expected load
C. Door style
D. Trim thickness
, Page 3 of 143
Answer: B
Rationale: Joist size depends mainly on the span, spacing, species or material, and loads the floor must
support.
3.
A carpenter notices that a wall opening is not square before installing a door. What should be done
first?
A. Install the door anyway
B. Correct the opening
C. Add more paint
D. Install the lock
Answer: B
Rationale: The rough opening should be properly sized, plumb, level, and square before the door is
installed.
4.
Which tool is commonly used to check whether a wall surface is vertically straight during framing?
, Page 4 of 143
A. Plumb level
B. Chisel
C. Nail set
D. Tin snips
Answer: A
Rationale: A level or plumb tool is used to check vertical alignment during wall framing.
5.
A carpenter is installing studs in a standard framed wall. What is the main purpose of maintaining
proper stud spacing?
A. Improve paint color
B. Provide structural support and proper sheathing attachment
C. Reduce door weight
D. Change ceiling height
Answer: B
Rationale: Correct stud spacing provides the intended wall strength and gives sheathing and finishes
proper support.
Arizona CR-7 Carpentry Contractor Exam Practice
Exam QUESTIONS AND VERIFIED ANSWERS WITH
RATIONALES JUST RELEASED
Arizona CR-7 Carpentry Contractor Exam Practice Questions
EXAM COVERAGE — 10 MOST-TESTED AREAS
1. Rough Carpentry and Structural Framing — Wall framing, floor framing, roof framing, studs,
plates, joists, rafters, beams, headers, blocking, bracing, layout, fastening, and structural
connections.
2. Finish Carpentry and Millwork — Interior trim, baseboards, casing, crown molding, cabinets,
countertops, paneling, stair trim, wood flooring, scribing, fitting, and finish quality.
3. Doors, Windows, and Hardware — Door installation, frames, hinges, locks, closers, window
installation, shimming, flashing, weatherproofing, alignment, and operation.
4. Plans, Measurements, Layout, and Calculations — Reading construction drawings, dimensions,
scales, square footage, linear measurements, material quantities, angles, elevations, and layout
procedures.
5. Wood Materials and Fasteners — Lumber grades, engineered wood, plywood, OSB, treated
lumber, nails, screws, bolts, anchors, adhesives, connectors, and selecting materials for the
application.
6. Roof and Floor Systems — Roof framing, trusses, rafters, sheathing, roof openings, floor joists,
subflooring, decking, blocking, and proper load transfer.
7. Exterior Carpentry and Weather Protection — Siding, exterior trim, flashing, moisture control,
caulking, window and door weatherproofing, decks, exterior wood protection, and drainage.
8. Metal Studs and Metal Door/Frame Work — Light-gauge metal framing, tracks, studs,
fastening, openings, door frames, alignment, reinforcement, and installation practices.
9. Safety, Tools, and Work Practices — Hand and power tools, ladders, scaffolds, PPE, fall
protection, electrical safety, housekeeping, material handling, and job-site hazards.
10. Arizona Contractor Responsibilities and Business Rules — CR-7 scope, qualifying-party
responsibilities, subcontracting work outside the classification, licensing, contracts, permits,
inspections, workmanship, and Arizona ROC requirements. (Arizona Registrar of Contractors)
1.
, Page 2 of 143
A carpenter is laying out a new wall before installing the studs. What should be checked first to keep the
wall correctly positioned?
A. Paint color
B. Wall dimensions and reference lines
C. Door hardware
D. Cabinet finish
Answer: B
Rationale: Wall dimensions and reference lines establish the correct location and size before studs are
installed.
2.
A floor joist must carry a load across an opening. Which condition is most important when selecting the
proper joist size?
A. Wall paint color
B. Span and expected load
C. Door style
D. Trim thickness
, Page 3 of 143
Answer: B
Rationale: Joist size depends mainly on the span, spacing, species or material, and loads the floor must
support.
3.
A carpenter notices that a wall opening is not square before installing a door. What should be done
first?
A. Install the door anyway
B. Correct the opening
C. Add more paint
D. Install the lock
Answer: B
Rationale: The rough opening should be properly sized, plumb, level, and square before the door is
installed.
4.
Which tool is commonly used to check whether a wall surface is vertically straight during framing?
, Page 4 of 143
A. Plumb level
B. Chisel
C. Nail set
D. Tin snips
Answer: A
Rationale: A level or plumb tool is used to check vertical alignment during wall framing.
5.
A carpenter is installing studs in a standard framed wall. What is the main purpose of maintaining
proper stud spacing?
A. Improve paint color
B. Provide structural support and proper sheathing attachment
C. Reduce door weight
D. Change ceiling height
Answer: B
Rationale: Correct stud spacing provides the intended wall strength and gives sheathing and finishes
proper support.
