NCCCO OSHA Crane Safety Exam Questions and Answers with Rationale Latest Edition 2026/2027

NCCCO OSHA Crane Safety Exam Questions and
Answers with Rationale Latest Edition 2026/2027


Question 1
According to OSHA 29 CFR 1926.1408, what is the minimum
required clearance distance for cranes operating near power lines
carrying up to 50 kV?
 A. 5 feet
 B. 10 feet
 C. 15 feet
 D. 20 feet
Correct Answer: B
Rationale: OSHA standards dictate a minimum clearance of 10
feet for power lines rated up to 50 kV to prevent catastrophic
electrical arcing and electrocution hazards.
Question 2
Under OSHA crane standards, who is explicitly responsible for
designating the inspection frequency, qualified personnel, and
ensuring that all required crane inspections are performed?
 A. The equipment manufacturer
 B. The crane operator alone
 C. The employer
 D. The local union representative
Correct Answer: C

,Rationale: OSHA places the ultimate administrative and safety
responsibility on the employer to establish regular inspection
protocols and assign qualified personnel.
Question 3
According to OSHA regulations, when must a comprehensive
annual inspection of a mobile crane be performed and
documented?
 A. Every month
 B. Every 6 months
 C. Every 12 months
 D. Every 5 years
Correct Answer: C
Rationale: OSHA mandates that a complete periodic/annual
inspection of cranes must be conducted at intervals not
exceeding 12 months, with written records kept on file.
Question 4
What OSHA subpart specifically governs cranes and derricks in
construction?
 A. Subpart C (General Safety)
 B. Subpart CC (Cranes and Derricks in Construction)
 C. Subpart K (Electrical)
 D. Subpart N (Helicopters)
Correct Answer: B

,Rationale: OSHA 29 CFR 1926 Subpart CC is the
comprehensive standard regulating the safe operation, assembly,
inspection, and certification of cranes in construction.
Question 5
Under OSHA rules, what must be done if a crane operator
discovers a safety defect during their pre-shift inspection?
 A. Continue operating until the end of the shift
 B. Attempt to weld or fix the defect themselves
 C. Take the equipment out of service immediately and tag
it out before any operation begins
 D. Report it at the weekly safety meeting
Correct Answer: C
Rationale: OSHA prohibits operating any crane with an
uncorrected safety deficiency; equipment must be immediately
tagged out of service.
Question 6
According to OSHA 1926.1417, when an operator leaves the
crane operating station unattended, what must be done with the
load, power, and controls?
 A. All controls must be in neutral, clutches disengaged,
power shut off or locked out, and any suspended load
landed.
 B. Leave the engine running to keep the batteries charged.
 C. Hang the pendant control over the hook.

,  D. Leave the load suspended mid-air with the brakes
locked.
Correct Answer: A
Rationale: Unattended cranes present severe runaway and drop
hazards; OSHA requires positive securing measures including
landing loads and de-energizing controls.
Question 7
When must a designated signal person be used during crane
operations under OSHA guidelines?
 A. Only during night shifts
 B. Whenever the operator's view is obstructed, when
operating in tight areas, or when directed by site safety
rules
 C. Signal persons are optional at all times
 D. Only for lifts exceeding 100 tons
Correct Answer: B
Rationale: OSHA requires qualified signal persons whenever
line-of-sight is blocked, blind spots exist, or complex
maneuvering is required near obstructions.
Question 8
According to OSHA standards, what type of fire extinguisher
must be accessible in the crane cab or on the equipment?
 A. Water-type extinguisher (Class A)