Cabinetmaking- NOCTI -Test
Questions All Solved Correctly.
Before applying finish, wood surfaces should be cleaned with - Answer A tack rag
On a router, the wedge device that holds the router bit in place is called a - Answer Collet
Use a ___ fire extinguisher for any fire involving paints, solvents, or finishing liquids - Answer
Class B
Set up a jig in the drill press when drilling - Answer Multiple items
What kind of dado only goes partially through a joint - Answer Blind
Radius cuts with a bandsaw should be cut - Answer 1/32 inch from the line on the waste side
Standard measurements for wall cabinets are - Answer 12 inches deep by 30 inches high
After cabinets are installed, nail holes on the trim are filled with - Answer Putty stick
A board with all 4 surfaces planed is specified as ____________. - Answer S4S
Raised panels with curved edges should be made using the - Answer Shaper
What is the maximum number of cabinet end panels (11-1/4 deep by 30 inches) that can be cut
from a single 4x8' sheet of plywood? - Answer 12
When boring deep holes in wood - Answer Back the drill out often to clear the wood chips
Which of the following tools is best used for cutting plastic laminate prior to final trimming -
Answer Table saw with high speed steel blade
If a laborer worked 40 hours at $8 per house and 4 hours overtime at 1-1/2 times regular pay,
the total pay before deductions is - Answer $368
Detail drawings should reference the - Answer Building cross section
, What is the cost per board foot if 26.66 board feet cost $14.75 - Answer $0.55
An electric motor can overheat and possibly cause a fire due to a - Answer Full load with the
motor running at half speed
The splitter on a table saw - Answer Prevents binding of stock
The "four penny" finishing nail is ___ long - Answer 1-1/2 inch
When using a dovetail template and a router to make drawers - Answer Place the router in the
template clear of the stock, start the router and cut the dovetail, and complete the cut without
lifting the router
The jointer out feed table must be set to the same height as the - Answer Jointer knives
When using a brush to apply finish, dip the bristles - Answer Halfway into the finish
In the construction of a spline joint, the grain of the spline should be - Answer At a 45-degree
angle
Pieces to be glued should first be clamped together without glue to - Answer Check the fit of
the joint
The operator should always make sure that the ___ is working before using a circular saw -
Answer Blade guard
The tool shown in the figure below is a ___ saw - Answer Back
Detail drawings - Answer Separate the individual parts that make up the finished object
What is the difference between dadoes and grooves - Answer Dadoes are cut across the grain
while grooves are cut with the grain
Using a euro-style hinge, the ___ would be the first adjustment - Answer Mounting hole
Questions All Solved Correctly.
Before applying finish, wood surfaces should be cleaned with - Answer A tack rag
On a router, the wedge device that holds the router bit in place is called a - Answer Collet
Use a ___ fire extinguisher for any fire involving paints, solvents, or finishing liquids - Answer
Class B
Set up a jig in the drill press when drilling - Answer Multiple items
What kind of dado only goes partially through a joint - Answer Blind
Radius cuts with a bandsaw should be cut - Answer 1/32 inch from the line on the waste side
Standard measurements for wall cabinets are - Answer 12 inches deep by 30 inches high
After cabinets are installed, nail holes on the trim are filled with - Answer Putty stick
A board with all 4 surfaces planed is specified as ____________. - Answer S4S
Raised panels with curved edges should be made using the - Answer Shaper
What is the maximum number of cabinet end panels (11-1/4 deep by 30 inches) that can be cut
from a single 4x8' sheet of plywood? - Answer 12
When boring deep holes in wood - Answer Back the drill out often to clear the wood chips
Which of the following tools is best used for cutting plastic laminate prior to final trimming -
Answer Table saw with high speed steel blade
If a laborer worked 40 hours at $8 per house and 4 hours overtime at 1-1/2 times regular pay,
the total pay before deductions is - Answer $368
Detail drawings should reference the - Answer Building cross section
, What is the cost per board foot if 26.66 board feet cost $14.75 - Answer $0.55
An electric motor can overheat and possibly cause a fire due to a - Answer Full load with the
motor running at half speed
The splitter on a table saw - Answer Prevents binding of stock
The "four penny" finishing nail is ___ long - Answer 1-1/2 inch
When using a dovetail template and a router to make drawers - Answer Place the router in the
template clear of the stock, start the router and cut the dovetail, and complete the cut without
lifting the router
The jointer out feed table must be set to the same height as the - Answer Jointer knives
When using a brush to apply finish, dip the bristles - Answer Halfway into the finish
In the construction of a spline joint, the grain of the spline should be - Answer At a 45-degree
angle
Pieces to be glued should first be clamped together without glue to - Answer Check the fit of
the joint
The operator should always make sure that the ___ is working before using a circular saw -
Answer Blade guard
The tool shown in the figure below is a ___ saw - Answer Back
Detail drawings - Answer Separate the individual parts that make up the finished object
What is the difference between dadoes and grooves - Answer Dadoes are cut across the grain
while grooves are cut with the grain
Using a euro-style hinge, the ___ would be the first adjustment - Answer Mounting hole
