Brigham Young University-Idaho Const 120 final || All Solutions are
Accurate.
Exterior house dimensions that are not evenly divided by four feet ________. correct answers
waste material
Interior partitions on building plans are usually ________. correct answers Dimensioned to their
centerlines
The anchor bolts should be set in the concrete ________. correct answers As soon as the concrete
is screeded
In order to prevent foundation forms from blowing out, the concrete should be placed ________.
correct answers In even layers inside the form
The metal units that hold the foundation forms an equal distance apart are called ________.
correct answers Snap ties
The width of a footing usually must be ________ the thickness of the foundation wall. correct
answers twice
In order to prevent footings from heaving and buckling they must be located ________. correct
answers Below the frost line
Concrete has very high ________. correct answers Compressive strength
Chemicals put into concrete to give it special properties are called ________. correct answers
Admixtures
A cubic yard contains ________ cubic feet. correct answers 27
,The quality of concrete is greatly affected by ________. correct answers The water to cement
ratio
Freezing of the water
Rapid evaporation of the water
All of the above
A chemical reaction called ________ causes cement to harden. correct answers Hydration
Hardening of concrete can continue for ________. correct answers Years
The most common drawing showing a horizontal cut through the building is called a ________.
correct answers floor plan
The roof slope indicated with materials notation for sheeting, roofing, insulation, soffit and
framing materials are typically found in the detail drawings. correct answers True
The perspective of a floor plan is one of a vertical cut made through the walls, 4-5 feet above the
floor. correct answers f
The quality of concrete is typically identified ________. correct answers In the specifications
The direction of stairway traffic flow ________. correct answers Is typically shown on the floor
plan
When the plan view, elevations, section view and details are put together they constitute a 3-D
perspective. correct answers t
"Green space" refers to the size of a building's footprint. correct answers f
, The laws which govern what type of structure may be built in a particular area are called
________. correct answers Zoning regulations
Hardships imposed by zoning regulations may be relieved by applying for a ________. correct
answers Variance
Blueprinting is a process of making copies of construction documents where the end result is
________. correct answers White lines on a blue background
The corner-to-corner, diagonal measurement of a rectangle whose measurements are 30'-0" x 40'-
0" is ________. correct answers 50'-0"
The identifying labels and locations of rooms (dining, bath, etc.) are typically found on the
________. correct answers Floor plan
The location of a building on the lot is determined from the ________. correct answers Site plan
Written documents which are the legal part of the construction documents are ________. correct
answers The specifications
A drawing showing a vertical cut through the building is called a ________. correct answers
section
An arrow designating North, and the location and bearing of property lines would typically be
shown on the ________. correct answers Site plan
A plan view of the footing location would typically be shown on the ________. correct answers
Foundation plan
Accurate.
Exterior house dimensions that are not evenly divided by four feet ________. correct answers
waste material
Interior partitions on building plans are usually ________. correct answers Dimensioned to their
centerlines
The anchor bolts should be set in the concrete ________. correct answers As soon as the concrete
is screeded
In order to prevent foundation forms from blowing out, the concrete should be placed ________.
correct answers In even layers inside the form
The metal units that hold the foundation forms an equal distance apart are called ________.
correct answers Snap ties
The width of a footing usually must be ________ the thickness of the foundation wall. correct
answers twice
In order to prevent footings from heaving and buckling they must be located ________. correct
answers Below the frost line
Concrete has very high ________. correct answers Compressive strength
Chemicals put into concrete to give it special properties are called ________. correct answers
Admixtures
A cubic yard contains ________ cubic feet. correct answers 27
,The quality of concrete is greatly affected by ________. correct answers The water to cement
ratio
Freezing of the water
Rapid evaporation of the water
All of the above
A chemical reaction called ________ causes cement to harden. correct answers Hydration
Hardening of concrete can continue for ________. correct answers Years
The most common drawing showing a horizontal cut through the building is called a ________.
correct answers floor plan
The roof slope indicated with materials notation for sheeting, roofing, insulation, soffit and
framing materials are typically found in the detail drawings. correct answers True
The perspective of a floor plan is one of a vertical cut made through the walls, 4-5 feet above the
floor. correct answers f
The quality of concrete is typically identified ________. correct answers In the specifications
The direction of stairway traffic flow ________. correct answers Is typically shown on the floor
plan
When the plan view, elevations, section view and details are put together they constitute a 3-D
perspective. correct answers t
"Green space" refers to the size of a building's footprint. correct answers f
, The laws which govern what type of structure may be built in a particular area are called
________. correct answers Zoning regulations
Hardships imposed by zoning regulations may be relieved by applying for a ________. correct
answers Variance
Blueprinting is a process of making copies of construction documents where the end result is
________. correct answers White lines on a blue background
The corner-to-corner, diagonal measurement of a rectangle whose measurements are 30'-0" x 40'-
0" is ________. correct answers 50'-0"
The identifying labels and locations of rooms (dining, bath, etc.) are typically found on the
________. correct answers Floor plan
The location of a building on the lot is determined from the ________. correct answers Site plan
Written documents which are the legal part of the construction documents are ________. correct
answers The specifications
A drawing showing a vertical cut through the building is called a ________. correct answers
section
An arrow designating North, and the location and bearing of property lines would typically be
shown on the ________. correct answers Site plan
A plan view of the footing location would typically be shown on the ________. correct answers
Foundation plan
