BMW ASSOCIATE LEVEL ASE EXAM 2026-2027
QUESTIONS AND ANSWERS RATED A+
✔✔Regarding a display vehicle check on a 2019 2 series
Tech A says that the digital compass and clock need to be set/calibrated
Tech B says that you need to activate and verify optional series xm satellite radio
(option 655) - ✔✔Both A and B
✔✔New Vehicle Prep can be found under the main group:
Maintenance and general info
Warranty
After sales
Information Systems - ✔✔Maintenance and general info
✔✔BMW special took 83 30 0 492 467 can be used during an inspection to measure:
Coolant level
Coolant concentrate
Brake pad thickness and tire thread depth
Air pressure - ✔✔Brake pad thickness and tire thread depth
✔✔Tech A states that during a Quality Certification 1 on a G05 X5 it is necessary to
press the 'AUTO' button in the light switch cluster.
Tech B states that during a Quality Certification 1 on a G05 X5 you can use the same
QC1 inspection sheet as a G02. - ✔✔Both A and B
✔✔If the vehicle is placed in transport mode and the vehicle battery voltage drops
below 12 volts (approximately 30% State of Charge), the "Replace Battery" message
will be displayed in the instrument cluster.
Tech A says that charging the battery back to 100% State of Charge and clearing faults
will remove the message from the instrument cluster.
Tech B says that running Energy Diagnosis and clearing faults will remove the message
from the instrument cluster. - ✔✔Neither A nor B
✔✔Transport Mode Switching Device can be used to successfully perform a QC1
inspection.
True or False? - ✔✔False
, ✔✔Tech A states that on 2019 Quality Certification 1 the DOT (Department of
Transportation) numbers from each tire's sidewall do not need to be recorded for
factory-fitted tires. The DOT numbers were recorded at the manufacturing plant and
stored in a proprietary database.
Tech B states that if a BMW-approved accessory wheel set is installed by the BMW
center prior to customer delivery, the DOT numbers from the accessory tires must be
recorded on an individually printed QC1 checklist. - ✔✔Both A and B
✔✔Vehicle history on a specific vehicle can be retrived from DCSnet.
Technician A says that the whole VIN number is required to access the information.
Technician B says that only the last 7 of the VIN are required to access the information.
Who is correct? - ✔✔B Only
✔✔According to MSDS warning symbols, the warning symbol with a skull and cross
bones shown represents - ✔✔Acute toxicity
✔✔All of the following are true concerning the Roundtable, EXCEPT :
There are 12 shows each year.
Each Roundtable has a bulletin describing the topics.
The Roundtable is accessed through AIR.
Each Roundtable has a quiz - ✔✔The Roundtable is accessed through AIR.
✔✔The TeileClearing list is updated if needed on :
The last day of the month.
The 25th of each month.
The 1st day of the month.
The 1st day of each quarter - ✔✔The 1st day of the month.
✔✔Technician A says that SIBs can be found in TIS under Service Information.
Technician B says that SIBs can be found in TIS under Technical Documentation.
Who is correct? - ✔✔A only
✔✔In TMSi, what is the path to check the progress of your BMW Technical Levels?
Technician A states that you can click on the Navigation Menu, select learning, view
your transcript, find the tab that says BMW Technical Levels Learning Path.Then, you
can either select the title BMW Technical Levels Learning Path or the Open Curriculum
tab to view your transcript.
QUESTIONS AND ANSWERS RATED A+
✔✔Regarding a display vehicle check on a 2019 2 series
Tech A says that the digital compass and clock need to be set/calibrated
Tech B says that you need to activate and verify optional series xm satellite radio
(option 655) - ✔✔Both A and B
✔✔New Vehicle Prep can be found under the main group:
Maintenance and general info
Warranty
After sales
Information Systems - ✔✔Maintenance and general info
✔✔BMW special took 83 30 0 492 467 can be used during an inspection to measure:
Coolant level
Coolant concentrate
Brake pad thickness and tire thread depth
Air pressure - ✔✔Brake pad thickness and tire thread depth
✔✔Tech A states that during a Quality Certification 1 on a G05 X5 it is necessary to
press the 'AUTO' button in the light switch cluster.
Tech B states that during a Quality Certification 1 on a G05 X5 you can use the same
QC1 inspection sheet as a G02. - ✔✔Both A and B
✔✔If the vehicle is placed in transport mode and the vehicle battery voltage drops
below 12 volts (approximately 30% State of Charge), the "Replace Battery" message
will be displayed in the instrument cluster.
Tech A says that charging the battery back to 100% State of Charge and clearing faults
will remove the message from the instrument cluster.
Tech B says that running Energy Diagnosis and clearing faults will remove the message
from the instrument cluster. - ✔✔Neither A nor B
✔✔Transport Mode Switching Device can be used to successfully perform a QC1
inspection.
True or False? - ✔✔False
, ✔✔Tech A states that on 2019 Quality Certification 1 the DOT (Department of
Transportation) numbers from each tire's sidewall do not need to be recorded for
factory-fitted tires. The DOT numbers were recorded at the manufacturing plant and
stored in a proprietary database.
Tech B states that if a BMW-approved accessory wheel set is installed by the BMW
center prior to customer delivery, the DOT numbers from the accessory tires must be
recorded on an individually printed QC1 checklist. - ✔✔Both A and B
✔✔Vehicle history on a specific vehicle can be retrived from DCSnet.
Technician A says that the whole VIN number is required to access the information.
Technician B says that only the last 7 of the VIN are required to access the information.
Who is correct? - ✔✔B Only
✔✔According to MSDS warning symbols, the warning symbol with a skull and cross
bones shown represents - ✔✔Acute toxicity
✔✔All of the following are true concerning the Roundtable, EXCEPT :
There are 12 shows each year.
Each Roundtable has a bulletin describing the topics.
The Roundtable is accessed through AIR.
Each Roundtable has a quiz - ✔✔The Roundtable is accessed through AIR.
✔✔The TeileClearing list is updated if needed on :
The last day of the month.
The 25th of each month.
The 1st day of the month.
The 1st day of each quarter - ✔✔The 1st day of the month.
✔✔Technician A says that SIBs can be found in TIS under Service Information.
Technician B says that SIBs can be found in TIS under Technical Documentation.
Who is correct? - ✔✔A only
✔✔In TMSi, what is the path to check the progress of your BMW Technical Levels?
Technician A states that you can click on the Navigation Menu, select learning, view
your transcript, find the tab that says BMW Technical Levels Learning Path.Then, you
can either select the title BMW Technical Levels Learning Path or the Open Curriculum
tab to view your transcript.
