Florida Unlimited Electrical (1-92)
(NEC) standards Exam Guide 2026
1. What is the wind stagnation pressure when the basic C. 31.0 psf
wind speed is 110 mph at a standard height of 33 feet?
A. 20.8 psf
B. 25.6 psf
C. 31.0 psf
D. 36.9 psf
2. metal letters are usually placed on a box, ap- C. Cutout
proximately six inches away from the background with
neon tubing placed behind the letters to outline them
without the tubing itself being visable.
A. Raised
B. Channel
C. Cutout
D. None of the above
3. Sloping or benching of excavations shall be designed D. More than 20'
by a registered engineer when depth of excavations is
.
A. More than 10'
B. More than 15'
C. At least 20'
D. More than 20'
4. The Americans with Disabilities Act is enforced by D. The Equal Employment
. Opportunity Commission
A. State police in individual states
B. The Federal Bureau of Investigation
, Florida Unlimited Electrical (1-92)
(NEC) standards Exam Guide 2026
C. The Fair Labor Standards Act
D. The Equal Employment Opportunity Commission
5. The MINMUM illumination for floors and walking sur- A. 1
faces, other than stairs, shall be to values of at least
ft-candle measured from the floor.
A. 1
B. 1 1/2
C. 0.2
D. 2 1/2
6. In the critical care (Category 1) spaces of health care fa- C. 10 AWG
cilities, a patient care vicinity shall be permitted to have
an optional equipment grounding point. An equip-
ment bonding jumper NOT small than shall be
used to connect the grounding terminal of all ground-
ing-type receptacles to the patient equipment ground-
ing point.
A. 14 AWG
B. 12 AWG
C. 10 AWG
D. 8 AWG
7. In the lubrication pit are of a minor repair commercial B. Class I, Division 2
garage where ventilation is not provided, the pit below
floor level shall be a location that extends up the
floor level.
A. Class I, Division 1
B. Class I, Division 2
, Florida Unlimited Electrical (1-92)
(NEC) standards Exam Guide 2026
C. Class II, Division 1
D. Class II, Division 2
8. Given: An equipment disconnecting means is mounted D. Unclassified
at a height of 6 feet on a remote wall in an aircraft stor-
age and maintenance hangar. The disconnect switch
is 10 feet horizontally from any aircraft fuel tanks. The
disconnect switch is 10 feet away from any aircraft fuel
tanks. The disconnect switch is located in a/an area.
A. Class II, Division 2
B. Class I, Division 2
C. Class I, Division 1
D. Unclassified
9. In motion picture studios, television studios and sim- D. 30
ilar locations, each receptacle of DC plugging boxes
shall be rated NOT less than ampheres.
A. 15
B. 20
C. 25
D. 30
10. The MAXIMUM weld size for a plate less than .25" is A. .0625
.
A. .0625
B. .0352
C. Depends on the thickness of the metal
D. Equal to the plate thickness
11. B. Encapsulation
(NEC) standards Exam Guide 2026
1. What is the wind stagnation pressure when the basic C. 31.0 psf
wind speed is 110 mph at a standard height of 33 feet?
A. 20.8 psf
B. 25.6 psf
C. 31.0 psf
D. 36.9 psf
2. metal letters are usually placed on a box, ap- C. Cutout
proximately six inches away from the background with
neon tubing placed behind the letters to outline them
without the tubing itself being visable.
A. Raised
B. Channel
C. Cutout
D. None of the above
3. Sloping or benching of excavations shall be designed D. More than 20'
by a registered engineer when depth of excavations is
.
A. More than 10'
B. More than 15'
C. At least 20'
D. More than 20'
4. The Americans with Disabilities Act is enforced by D. The Equal Employment
. Opportunity Commission
A. State police in individual states
B. The Federal Bureau of Investigation
, Florida Unlimited Electrical (1-92)
(NEC) standards Exam Guide 2026
C. The Fair Labor Standards Act
D. The Equal Employment Opportunity Commission
5. The MINMUM illumination for floors and walking sur- A. 1
faces, other than stairs, shall be to values of at least
ft-candle measured from the floor.
A. 1
B. 1 1/2
C. 0.2
D. 2 1/2
6. In the critical care (Category 1) spaces of health care fa- C. 10 AWG
cilities, a patient care vicinity shall be permitted to have
an optional equipment grounding point. An equip-
ment bonding jumper NOT small than shall be
used to connect the grounding terminal of all ground-
ing-type receptacles to the patient equipment ground-
ing point.
A. 14 AWG
B. 12 AWG
C. 10 AWG
D. 8 AWG
7. In the lubrication pit are of a minor repair commercial B. Class I, Division 2
garage where ventilation is not provided, the pit below
floor level shall be a location that extends up the
floor level.
A. Class I, Division 1
B. Class I, Division 2
, Florida Unlimited Electrical (1-92)
(NEC) standards Exam Guide 2026
C. Class II, Division 1
D. Class II, Division 2
8. Given: An equipment disconnecting means is mounted D. Unclassified
at a height of 6 feet on a remote wall in an aircraft stor-
age and maintenance hangar. The disconnect switch
is 10 feet horizontally from any aircraft fuel tanks. The
disconnect switch is 10 feet away from any aircraft fuel
tanks. The disconnect switch is located in a/an area.
A. Class II, Division 2
B. Class I, Division 2
C. Class I, Division 1
D. Unclassified
9. In motion picture studios, television studios and sim- D. 30
ilar locations, each receptacle of DC plugging boxes
shall be rated NOT less than ampheres.
A. 15
B. 20
C. 25
D. 30
10. The MAXIMUM weld size for a plate less than .25" is A. .0625
.
A. .0625
B. .0352
C. Depends on the thickness of the metal
D. Equal to the plate thickness
11. B. Encapsulation
