After a bullet leaves the rifle barrel, what two forces act on the bullet's trajectory gravity and the force due to the air
Which reloading scale is accurate, inexpensive, and not attected by changes in atmospheric
pressure?
a. An electronic scale A beam scale
b. A beam scale
c. A kitchen scale
d. A spring scale
The sizing die is and needs to be fitted into an appropriate reloading press.
a. Temperature-sensitive
Cartridge-specific
b. Cartridge-specific
c. Crimped
d. Thermocoupled
Full-length sizing die setup begins by inserting the into the top of the press's ram.
a. Trim die
Shellholder
b. Decapping pin
c. Case lube
d. Shellholder
The measurement for overall case length is taken from the flat of the case head to the
opening of the case mouth, and the length is always expressed as a maximum dimension
less .
Ten-thousandths of an inch
a. Ten-thousandths of an inch
b. One-tenth of an inch
c. One one-thousandths of an inch
d. Ten-thousandths of a milliliter
Which process compresses metal and reforms it to a specified dimension?
a. Soft-seating
Resizing
b. Cam-over
c. Decapping
d. Resizing
What is the proper name for a bullet tip
a. The meplat
The meplat
b. The cam
c. The head
d. The point
What is the name for backing ott the ram slightly and screwing in the die an additional 1/8-
to ¼-turn?
a. Soft-seating Cam-over
b. Cam-over
c. Decapping
d. Crimping
TRUE
1/8
, True or False
The cleaning of the primer pocket cannot be done until the primer is removed.
True or False
To achieve proper obturation on a resized case, it is preferable to focus on the dimensions of TRUE
a minimum chamber specification, one that has only the slightest clearance needed to easily
and safely chamber the round.
The sizing die is and needs to be fitted into an appropriate reloading press.
a. Trimming
None of the above
b. Crimping
c. Heating
d. None of the above
TRUE OR FALSE
TRUE
The shellholder is specific not to caliber, but rather to the dimensions of the case head
For most presses with the priming feature, which way should the primer anvil be facing?
a. It should be facing up
It should be facing up
b. It should be facing down
c. It should be facing you
d. None of the above
What will using the dial or electronic caliper and measuring the case from the meplat to the
flat of the case head where the primer is located do?
a. Help you decide whether you need to use a roll crimp instead of a taper crimp It will give you the COL measurement of the loaded round after soft-seating
b. It will give you the COL measurement of the loaded round after soft-seating
c. It will give you the COL measurement of the loaded round before soft-seating
d. There is no need to take such a measurement
Which of the following measures the radial run out of a finished round?
a. A Hornady scale
A concentricity gauge
b. A thermocoupler
c. A concentricity gauge
d. An EGT gauge
Which of the following tools returns the expanded brass to a reusable state?
a. The resizing die The resizing die
b. The shellholder
c. The crimp ring
d. The trickler
Which of the following should not be done with a carbide die?
a. The use of a locking ring
Cam-over
b. Cam-over
c. Cam-under
d. None of the above
2/8
Which reloading scale is accurate, inexpensive, and not attected by changes in atmospheric
pressure?
a. An electronic scale A beam scale
b. A beam scale
c. A kitchen scale
d. A spring scale
The sizing die is and needs to be fitted into an appropriate reloading press.
a. Temperature-sensitive
Cartridge-specific
b. Cartridge-specific
c. Crimped
d. Thermocoupled
Full-length sizing die setup begins by inserting the into the top of the press's ram.
a. Trim die
Shellholder
b. Decapping pin
c. Case lube
d. Shellholder
The measurement for overall case length is taken from the flat of the case head to the
opening of the case mouth, and the length is always expressed as a maximum dimension
less .
Ten-thousandths of an inch
a. Ten-thousandths of an inch
b. One-tenth of an inch
c. One one-thousandths of an inch
d. Ten-thousandths of a milliliter
Which process compresses metal and reforms it to a specified dimension?
a. Soft-seating
Resizing
b. Cam-over
c. Decapping
d. Resizing
What is the proper name for a bullet tip
a. The meplat
The meplat
b. The cam
c. The head
d. The point
What is the name for backing ott the ram slightly and screwing in the die an additional 1/8-
to ¼-turn?
a. Soft-seating Cam-over
b. Cam-over
c. Decapping
d. Crimping
TRUE
1/8
, True or False
The cleaning of the primer pocket cannot be done until the primer is removed.
True or False
To achieve proper obturation on a resized case, it is preferable to focus on the dimensions of TRUE
a minimum chamber specification, one that has only the slightest clearance needed to easily
and safely chamber the round.
The sizing die is and needs to be fitted into an appropriate reloading press.
a. Trimming
None of the above
b. Crimping
c. Heating
d. None of the above
TRUE OR FALSE
TRUE
The shellholder is specific not to caliber, but rather to the dimensions of the case head
For most presses with the priming feature, which way should the primer anvil be facing?
a. It should be facing up
It should be facing up
b. It should be facing down
c. It should be facing you
d. None of the above
What will using the dial or electronic caliper and measuring the case from the meplat to the
flat of the case head where the primer is located do?
a. Help you decide whether you need to use a roll crimp instead of a taper crimp It will give you the COL measurement of the loaded round after soft-seating
b. It will give you the COL measurement of the loaded round after soft-seating
c. It will give you the COL measurement of the loaded round before soft-seating
d. There is no need to take such a measurement
Which of the following measures the radial run out of a finished round?
a. A Hornady scale
A concentricity gauge
b. A thermocoupler
c. A concentricity gauge
d. An EGT gauge
Which of the following tools returns the expanded brass to a reusable state?
a. The resizing die The resizing die
b. The shellholder
c. The crimp ring
d. The trickler
Which of the following should not be done with a carbide die?
a. The use of a locking ring
Cam-over
b. Cam-over
c. Cam-under
d. None of the above
2/8
