Telehandler Operator (NCCCO-AMP) Certification
Telehandler Operator (NCCCO-AMP) Certification
1. What is the primary function that distinguishes a telehandler from a
standard forklift?
A. A telescoping boom that extends horizontally and vertically
B. A four-wheel steering axle
C. An enclosed operator cab
D. A hydraulic tilt cylinder on the mast
2. What is the common industry term for a telehandler's extendable arm?
A. Mast
B. Jib
C. Derrick
D. Boom
3. Which of the following best describes 'reach' on a telehandler?
A. The distance the machine can travel in one hour
B. The maximum height the boom can achieve
C. The width of the outrigger footprint
D. The horizontal distance from the front axle (or rated point) to the load
4. What does the term 'rated capacity' refer to on a telehandler?
A. The maximum speed the machine can travel while loaded
B. The maximum load the machine can lift safely at a given boom angle
and extension
C. The volume of hydraulic fluid the system holds
D. The weight of the machine itself
Page 1 of 42
, Telehandler Operator (NCCCO-AMP) Certification
5. On a telehandler, what is the 'load moment'?
A. The angle of the boom relative to the chassis
B. The torque produced by the engine at idle
C. The time it takes to lift a load to full height
D. The product of the load weight and the horizontal distance from the
tipping fulcrum
6. What is the 'tipping fulcrum' on a telehandler?
A. The pivot point of the boom cylinder
B. The center of the steering axle
C. The point around which the machine would rotate if it became unstable
D. The attachment point of the carriage
7. Which term describes the carriage-mounted device used to engage a pallet
or load?
A. Sheave
B. Boom head
C. Outrigger pad
D. Forks
8. What is a 'quick-attach' or 'quick-coupler' system used for on a
telehandler?
A. Connecting the boom to the chassis
B. Attaching outriggers to the frame
C. Quickly refueling the machine
D. Rapidly changing attachments without tools
9. What does 'ground bearing pressure' refer to?
A. The pressure the operator applies to the foot pedal
B. The air pressure inside the tires
C. The force per unit area the machine's tires or tracks exert on the
supporting surface
D. The hydraulic pressure in the lift cylinder
10. In telehandler terminology, what is 'crowd'?
A. Tilting the carriage or forks backward toward the machine
B. Rotating the machine chassis
C. Lowering the boom rapidly
Page 2 of 42
, Telehandler Operator (NCCCO-AMP) Certification
D. Extending the boom outward
11. What is 'dump' in relation to fork/carriage movement?
A. Emptying the fuel tank
B. Retracting the boom fully
C. Tilting the carriage or forks forward, away from the machine
D. Releasing the parking brake
12. What is the purpose of the 'load moment indicator' (LMI) or similar rated
capacity indicator system?
A. To warn the operator when approaching the machine's stability or
capacity limit
B. To indicate tire pressure
C. To measure fuel consumption
D. To display the engine's RPM
13. What does 'articulated frame steering' mean on some telehandlers?
A. Only the rear wheels turn
B. The chassis pivots at a joint between the front and rear sections to steer
C. Steering is achieved solely through differential braking
D. The boom itself rotates to steer the machine
14. What is the function of a telehandler's stabilizers (outriggers)?
A. To increase the machine's effective footprint and stability when lifting
B. To support the counterweight during transport
C. To provide additional traction in mud
D. To cool the hydraulic system
15. What is 'two-wheel steer' mode typically used for on a telehandler?
A. Tight maneuvering in confined spaces
B. Operating exclusively with attachments
C. Standard travel and roading on firm surfaces
D. Crab steering for lateral movement only
16. What is 'crab steer' mode used for?
A. Increasing lift capacity
B. Climbing steep grades safely
C. Locking the steering for transport
Page 3 of 42
, Telehandler Operator (NCCCO-AMP) Certification
D. Moving the machine diagonally without changing chassis orientation
17. Which component transmits hydraulic power to extend and retract the
boom?
A. Parking brake actuator
B. Differential lock cylinder
C. Steering cylinder
D. Telescoping (extend/retract) cylinder
18. What does 'counterweight' refer to on a telehandler?
A. The operator's body weight
B. An attachment used to test stability
C. Mass positioned at the rear of the machine to offset the load moment
D. The weight of the boom itself
19. What is the typical purpose of a telehandler compared to a rough-terrain
forklift?
A. Operation without an engine
B. Greater reach and lift height for placing loads at elevation or extended
distance
C. Exclusive use with man-baskets
D. Lower ground clearance for paved surfaces only
20. What does 'carry position' mean when traveling with a load?
A. Boom rotated to the side
B. Boom lowered and retracted, load close to the ground and tilted back
C. Boom fully raised and extended
D. Load resting directly on the ground while moving
21. As boom extension increases with a constant load, what happens to the
machine's stability?
A. Stability increases due to lower center of gravity
B. Stability only depends on boom angle, not extension
C. Stability remains constant regardless of extension
D. Stability decreases because the load moment increases
22. What generally happens to rated capacity as the boom is raised and
extended further from the machine?
A. Rated capacity stays the same
Page 4 of 42
Telehandler Operator (NCCCO-AMP) Certification
1. What is the primary function that distinguishes a telehandler from a
standard forklift?
A. A telescoping boom that extends horizontally and vertically
B. A four-wheel steering axle
C. An enclosed operator cab
D. A hydraulic tilt cylinder on the mast
2. What is the common industry term for a telehandler's extendable arm?
A. Mast
B. Jib
C. Derrick
D. Boom
3. Which of the following best describes 'reach' on a telehandler?
A. The distance the machine can travel in one hour
B. The maximum height the boom can achieve
C. The width of the outrigger footprint
D. The horizontal distance from the front axle (or rated point) to the load
4. What does the term 'rated capacity' refer to on a telehandler?
A. The maximum speed the machine can travel while loaded
B. The maximum load the machine can lift safely at a given boom angle
and extension
C. The volume of hydraulic fluid the system holds
D. The weight of the machine itself
Page 1 of 42
, Telehandler Operator (NCCCO-AMP) Certification
5. On a telehandler, what is the 'load moment'?
A. The angle of the boom relative to the chassis
B. The torque produced by the engine at idle
C. The time it takes to lift a load to full height
D. The product of the load weight and the horizontal distance from the
tipping fulcrum
6. What is the 'tipping fulcrum' on a telehandler?
A. The pivot point of the boom cylinder
B. The center of the steering axle
C. The point around which the machine would rotate if it became unstable
D. The attachment point of the carriage
7. Which term describes the carriage-mounted device used to engage a pallet
or load?
A. Sheave
B. Boom head
C. Outrigger pad
D. Forks
8. What is a 'quick-attach' or 'quick-coupler' system used for on a
telehandler?
A. Connecting the boom to the chassis
B. Attaching outriggers to the frame
C. Quickly refueling the machine
D. Rapidly changing attachments without tools
9. What does 'ground bearing pressure' refer to?
A. The pressure the operator applies to the foot pedal
B. The air pressure inside the tires
C. The force per unit area the machine's tires or tracks exert on the
supporting surface
D. The hydraulic pressure in the lift cylinder
10. In telehandler terminology, what is 'crowd'?
A. Tilting the carriage or forks backward toward the machine
B. Rotating the machine chassis
C. Lowering the boom rapidly
Page 2 of 42
, Telehandler Operator (NCCCO-AMP) Certification
D. Extending the boom outward
11. What is 'dump' in relation to fork/carriage movement?
A. Emptying the fuel tank
B. Retracting the boom fully
C. Tilting the carriage or forks forward, away from the machine
D. Releasing the parking brake
12. What is the purpose of the 'load moment indicator' (LMI) or similar rated
capacity indicator system?
A. To warn the operator when approaching the machine's stability or
capacity limit
B. To indicate tire pressure
C. To measure fuel consumption
D. To display the engine's RPM
13. What does 'articulated frame steering' mean on some telehandlers?
A. Only the rear wheels turn
B. The chassis pivots at a joint between the front and rear sections to steer
C. Steering is achieved solely through differential braking
D. The boom itself rotates to steer the machine
14. What is the function of a telehandler's stabilizers (outriggers)?
A. To increase the machine's effective footprint and stability when lifting
B. To support the counterweight during transport
C. To provide additional traction in mud
D. To cool the hydraulic system
15. What is 'two-wheel steer' mode typically used for on a telehandler?
A. Tight maneuvering in confined spaces
B. Operating exclusively with attachments
C. Standard travel and roading on firm surfaces
D. Crab steering for lateral movement only
16. What is 'crab steer' mode used for?
A. Increasing lift capacity
B. Climbing steep grades safely
C. Locking the steering for transport
Page 3 of 42
, Telehandler Operator (NCCCO-AMP) Certification
D. Moving the machine diagonally without changing chassis orientation
17. Which component transmits hydraulic power to extend and retract the
boom?
A. Parking brake actuator
B. Differential lock cylinder
C. Steering cylinder
D. Telescoping (extend/retract) cylinder
18. What does 'counterweight' refer to on a telehandler?
A. The operator's body weight
B. An attachment used to test stability
C. Mass positioned at the rear of the machine to offset the load moment
D. The weight of the boom itself
19. What is the typical purpose of a telehandler compared to a rough-terrain
forklift?
A. Operation without an engine
B. Greater reach and lift height for placing loads at elevation or extended
distance
C. Exclusive use with man-baskets
D. Lower ground clearance for paved surfaces only
20. What does 'carry position' mean when traveling with a load?
A. Boom rotated to the side
B. Boom lowered and retracted, load close to the ground and tilted back
C. Boom fully raised and extended
D. Load resting directly on the ground while moving
21. As boom extension increases with a constant load, what happens to the
machine's stability?
A. Stability increases due to lower center of gravity
B. Stability only depends on boom angle, not extension
C. Stability remains constant regardless of extension
D. Stability decreases because the load moment increases
22. What generally happens to rated capacity as the boom is raised and
extended further from the machine?
A. Rated capacity stays the same
Page 4 of 42
