BMW MEMBERS EXAM 2026/2027 –
COMPLETE QUESTIONS AND ANSWERS
FULL TEST BANK VERIFIED EDITION.
◎ When testing for source voltage, the DVOM should be set to:
AC voltage
DC voltage
AC amp
DC amp. ANSWER:- DC voltage
◎ Two technicians are discussing the KL terminals:
Technician A states that KL30 indicates hot all times
Technician B states KL31indcates a permanent ground.
Who's correct?. ANSWER:- Both
◎ When installing a new battery in a BMW, with the same capacity, we need to:
Register the new battery
Register and retrofit the new battery
Program the vehicle for the new battery
None of the above.. ANSWER:- Register the new battery
◎ ALL the following statements are correct when installing a V-cable to a module,
EXCEPT:
The vehicle must be in KL0.
Vehicle has to be at sleep.
Vehicle needs to be in PAD mode
Battery should be disconnected.. ANSWER:- Vehicle needs to be in PAD mode
◎ All these checks should be performed when using a DVOM, EXCEPT:
Check the meter's battery
Visual inspection of the leads
Meter leads should be tested for no less than 1Ω of resistance
Check the meter's internal fuses. ANSWER:- Meter leads should be tested for no less
than 1Ω of resistance
◎ Two technicians are discussing an electrical diagnostic process,
Technician A states that for you to diagnoses an electrical problem an ABL should be
performed.
Technician B states the technician, if needed can find the correct SSP inside the ABL.
Who's correct?. ANSWER:- Both
◎ Two technicians are discussing the pin assignment chart:
Technician A states that the letter E stands for Electrical
, Technician B states that the letter E stands for Input.
Who's correct?. ANSWER:- Technician B
◎ BMW recommends that an AGM battery's SOC never drops below?
12.5 V
12.0 V
13.1 V
11.0 V. ANSWER:- 12.5 V
◎ Two technicians are discussing removing a battery cable.
Technician A states that BMW recommends the technician waits for the vehicle to go to
sleep before disconnecting the cable.
Technician B states that once the key is removed from the vehicle it is safe to remove
the battery cable.
Who's correct?. ANSWER:- Technician A
◎ Two technicians are discussing Available voltage:
Technician A states that available voltage should be within .3v of source voltage.
Technician B states that available voltage should be within 1v of source voltage.
Who's correct?. ANSWER:- Technician A
◎ Two technicians are discussing source voltage:
Technician A states that source voltage can be measured at the component and a
known good ground
Technician B states that source voltage should be measured at the positive and
negative pole on the battery.
Who's correct?. ANSWER:- Technician B
◎ When performing a diagnosis on a BMW, it is recommended to always have a
battery charger connected to the vehicle?
True
False. ANSWER:- True
◎ What is the purpose of the IBS?
To determine SoC, SoH and temp of the battery.
Measures the charging voltage from the alternator.
Maintain the correct charge on the battery
All of the above. ANSWER:- All of the above
◎ When performing a Voltage Drop measurement, the circuit needs to be active.
True
False. ANSWER:- True
◎ When replacing the IBS, the technician will need to:
Program the IBS to the vehicle
COMPLETE QUESTIONS AND ANSWERS
FULL TEST BANK VERIFIED EDITION.
◎ When testing for source voltage, the DVOM should be set to:
AC voltage
DC voltage
AC amp
DC amp. ANSWER:- DC voltage
◎ Two technicians are discussing the KL terminals:
Technician A states that KL30 indicates hot all times
Technician B states KL31indcates a permanent ground.
Who's correct?. ANSWER:- Both
◎ When installing a new battery in a BMW, with the same capacity, we need to:
Register the new battery
Register and retrofit the new battery
Program the vehicle for the new battery
None of the above.. ANSWER:- Register the new battery
◎ ALL the following statements are correct when installing a V-cable to a module,
EXCEPT:
The vehicle must be in KL0.
Vehicle has to be at sleep.
Vehicle needs to be in PAD mode
Battery should be disconnected.. ANSWER:- Vehicle needs to be in PAD mode
◎ All these checks should be performed when using a DVOM, EXCEPT:
Check the meter's battery
Visual inspection of the leads
Meter leads should be tested for no less than 1Ω of resistance
Check the meter's internal fuses. ANSWER:- Meter leads should be tested for no less
than 1Ω of resistance
◎ Two technicians are discussing an electrical diagnostic process,
Technician A states that for you to diagnoses an electrical problem an ABL should be
performed.
Technician B states the technician, if needed can find the correct SSP inside the ABL.
Who's correct?. ANSWER:- Both
◎ Two technicians are discussing the pin assignment chart:
Technician A states that the letter E stands for Electrical
, Technician B states that the letter E stands for Input.
Who's correct?. ANSWER:- Technician B
◎ BMW recommends that an AGM battery's SOC never drops below?
12.5 V
12.0 V
13.1 V
11.0 V. ANSWER:- 12.5 V
◎ Two technicians are discussing removing a battery cable.
Technician A states that BMW recommends the technician waits for the vehicle to go to
sleep before disconnecting the cable.
Technician B states that once the key is removed from the vehicle it is safe to remove
the battery cable.
Who's correct?. ANSWER:- Technician A
◎ Two technicians are discussing Available voltage:
Technician A states that available voltage should be within .3v of source voltage.
Technician B states that available voltage should be within 1v of source voltage.
Who's correct?. ANSWER:- Technician A
◎ Two technicians are discussing source voltage:
Technician A states that source voltage can be measured at the component and a
known good ground
Technician B states that source voltage should be measured at the positive and
negative pole on the battery.
Who's correct?. ANSWER:- Technician B
◎ When performing a diagnosis on a BMW, it is recommended to always have a
battery charger connected to the vehicle?
True
False. ANSWER:- True
◎ What is the purpose of the IBS?
To determine SoC, SoH and temp of the battery.
Measures the charging voltage from the alternator.
Maintain the correct charge on the battery
All of the above. ANSWER:- All of the above
◎ When performing a Voltage Drop measurement, the circuit needs to be active.
True
False. ANSWER:- True
◎ When replacing the IBS, the technician will need to:
Program the IBS to the vehicle
