General Contractor LicenseGeneral
KB2 Study
Contractor
Prep FullLicense
Set –
General
KB2
Practice
Study
Contractor
Questions
Prep Full
License
&
Set
Exam
–KB2
Practice
Guide
Study
PDF.pdf
Questions
Prep Full &
Set
Exam
– Practice
Guide PDF.pdf
Questions & Exam Guide PDF.pdf
General Contractor License KB2 Study
Prep Full Set – Practice Questions &
Exam Guide PDF
Guidehttps://www.stuvia.com/dashboard!@_)#*)(@$)($@*($@)($@*_
General Contractor LicenseGeneral
KB2 Study
Contractor
Prep FullLicense
Set –
General
KB2
Practice
Study
Contractor
Questions
Prep Full
License
&
Set
Exam
–KB2
Practice
Guide
Study
PDF.pdf
Questions
Prep Full &
Set
Exam
– Practice
Guide PDF.pdf
Questions & Exam Guide PDF.pdf
,General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf
At what stage of the construction process would the after the wall has been erected and braced
builder cut out the sole plate in a door opening?
When wide square edge boards are being used for to only one siding board
board and batten siding, how should the batten strips
be nailed ?
According to the code, the minimum allowable height of 42
a guardrail at a restaurant deck (or any commercial
building) is _____ inches above the finished floor height of
the deck or balcony.
General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf
,General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf
If the blueprint does not disclose an exterior doors 2 inches
rough opening, then the standard practice would be to
frame the width _____ oversize.
How are resilient channels used in drywall application? to decrease sound transmission in walls and partitions
What screws are used to attach steel studs to the top pan head, type S. It attaches stud to runner up to 14-ga
and bottom steel track?
In single family dwelling sleeping rooms, the minimum 20
net clear opening width of windows, which are required
for emergency egress or rescue, is _____ inches.
According to the code what is the minimum slope on 2:12
which asphalt strip shingles may be installed?
According to Code the MAXIMUM diameter of a hole 3
that may be bored in a 2 by 10 joist is _____ inches.
General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf
, General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf
According to the Code, notches allowed in the top or 1/6
bottom of joists shall not exceed what fraction of the
depth of the joist?
While trenching and excavating, OSHA requires at least 2 feet
_____ feet of clear unobstructed distance from the
trenches edge to the toe or edge of the dirt or spoils
pile.
What is the actual size of a 2 x 4 surfaced dry piece of 1-1/2 by 3-1/2
framing lumber?
General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf
KB2 Study
Contractor
Prep FullLicense
Set –
General
KB2
Practice
Study
Contractor
Questions
Prep Full
License
&
Set
Exam
–KB2
Practice
Guide
Study
PDF.pdf
Questions
Prep Full &
Set
Exam
– Practice
Guide PDF.pdf
Questions & Exam Guide PDF.pdf
General Contractor License KB2 Study
Prep Full Set – Practice Questions &
Exam Guide PDF
Guidehttps://www.stuvia.com/dashboard!@_)#*)(@$)($@*($@)($@*_
General Contractor LicenseGeneral
KB2 Study
Contractor
Prep FullLicense
Set –
General
KB2
Practice
Study
Contractor
Questions
Prep Full
License
&
Set
Exam
–KB2
Practice
Guide
Study
PDF.pdf
Questions
Prep Full &
Set
Exam
– Practice
Guide PDF.pdf
Questions & Exam Guide PDF.pdf
,General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf
At what stage of the construction process would the after the wall has been erected and braced
builder cut out the sole plate in a door opening?
When wide square edge boards are being used for to only one siding board
board and batten siding, how should the batten strips
be nailed ?
According to the code, the minimum allowable height of 42
a guardrail at a restaurant deck (or any commercial
building) is _____ inches above the finished floor height of
the deck or balcony.
General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf
,General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf
If the blueprint does not disclose an exterior doors 2 inches
rough opening, then the standard practice would be to
frame the width _____ oversize.
How are resilient channels used in drywall application? to decrease sound transmission in walls and partitions
What screws are used to attach steel studs to the top pan head, type S. It attaches stud to runner up to 14-ga
and bottom steel track?
In single family dwelling sleeping rooms, the minimum 20
net clear opening width of windows, which are required
for emergency egress or rescue, is _____ inches.
According to the code what is the minimum slope on 2:12
which asphalt strip shingles may be installed?
According to Code the MAXIMUM diameter of a hole 3
that may be bored in a 2 by 10 joist is _____ inches.
General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf
, General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf
According to the Code, notches allowed in the top or 1/6
bottom of joists shall not exceed what fraction of the
depth of the joist?
While trenching and excavating, OSHA requires at least 2 feet
_____ feet of clear unobstructed distance from the
trenches edge to the toe or edge of the dirt or spoils
pile.
What is the actual size of a 2 x 4 surfaced dry piece of 1-1/2 by 3-1/2
framing lumber?
General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf General Contractor License - KB2 Study Prep - Full Set.pdf
