PACrane OperatorLicensing Examination Qu
j j j j j
estions And Correct Answers (Verified Answe
j j j j j
rs) Plus Rationales 2026|2027 Q&A | Instant
j j j j j j j
Download Pdf j
1. What is the primary purpose of a crane load chart?
j j j j j j j j j j
a) To show the crane’s engine specifications
j j j j j
b) To indicate the crane’s counterweight size
j j j j j
c) To determine the crane’s lifting capacities at various co
j j j j j j j j
nfigurations
d) To calculate wire rope strength
j j j j
The load chart provides the crane operator with lifting capacities at differe
j j j j j j j j j j j
nt boom lengths, radii, and configurations to ensure safe operation.
j j j j j j j j j
2. What does the term "working radius" mean in crane operation?
j j j j j j j j j
a) The distance between the crane cab and the ground
j j j j j j j j
b) The horizontal distance from the center of rotation to the center of t
j j j j j j j j j j j j
he load j
, c) The distance the boom can extend vertically
j j j j j j
d) The counterweight’s effective range
j j j
Working radius is measured horizontally from the crane’s center of rotatio
j j j j j j j j j j
n to the load’s center, and it directly affects lifting capacity.
j j j j j j j j j j
3. When operating a mobile crane on outriggers, the crane’s capacity is bas
j j j j j j j j j j j
ed on:
j
a) The ground condition only
j j j
b) The counterweight size only
j j j
c) The crane’s load chart for “on outriggers” configuration
j j j j j j j
d) The boom angle only j j j
Capacity is determined from the manufacturer’s load chart specific to the o
j j j j j j j j j j j
utrigger setup. j
4. Which of the following ground conditions is most dangerous for crane set
j j j j j j j j j j j
up?
a) Compacted gravel j
b) Concrete pad j
c) Soft or uncompacted soil j j j
d) Asphalt over crushed stone j j j
Soft or uncompacted soil may not support the crane’s weight, leading to ins
j j j j j j j j j j j j
tability and possible overturning.
j j j
5. What does "D/d ratio" refer to in crane operations?
j j j j j j j j
a) The drum size to load size ratio
j j j j j j
b) The ratio of the diameter of the sheave to the diameter of the
j j j j j j j j j j j j
, rope
c) The load chart ratio of duty cycle to design
j j j j j j j j
d) The outrigger span to crane height ratio
j j j j j j
The D/d ratio ensures wire rope bends around sheaves of sufficient size to p
j j j j j j j j j j j j j
revent rope fatigue and damage. j j j j
6. What is the purpose of a boom angle indicator?
j j j j j j j j
a) To measure wind speed
j j j
b) To show the angle of the boom relative to the ground
j j j j j j j j j j
c) To determine counterweight requirements
j j j
d) To calculate load radius automatically
j j j j
A boom angle indicator allows the operator to determine the radius, which
j j j j j j j j j j j
is essential for safe lifting based on the load chart.
j j j j j j j j j j
7. OSHA requires a signal person when:
j j j j j
a) The load is under 500 lbs j j j j j
b) The operator has a clear line of sight
j j j j j j j
c) The operator’s view of the load or path is obstructed
j j j j j j j j j
d) The lift is less than 10 feet j j j j j j
A signal person is required when the operator cannot see the load or path, e
j j j j j j j j j j j j j j
nsuring communication for safe movement. j j j j
8. Which hand signal universally means "emergency stop"?
j j j j j j
a) Arm extended forward with palm down, moving up and down
j j j j j j j j j
b) Arm extended with palm down, moved rapidly back and forth
j j j j j j j j j
c) Arm extended upward, pointing with one finger
j j j j j j
, d) Arm circling overhead j j
The emergency stop signal is standardized as an arm extended with palm d
j j j j j j j j j j j j
own, moved rapidly side to side.
j j j j j
9. What is the function of the anti-two-block device?
j j j j j j j
a) To prevent load line from unspooling
j j j j j
b) To prevent the hook block from contacting the boom tip
j j j j j j j j j
c) To stop the crane from exceeding load chart capacity
j j j j j j j j
d) To measure boom deflection
j j j
The anti-two-
j
block device prevents dangerous contact between the hook block and boo
j j j j j j j j j j
m tip, which could break the rope.
j j j j j j
10. What is the best method to verify the weight of a load before liftin
j j j j j j j j j j j j j
g?
a) Estimate based on appearance j j j
b) Check shipping papers, drawings, or manufacturer’s data
j j j j j j
c) Ask the rigger j j
d) Perform a test lift j j j
Using official documentation is the most accurate method for verifying loa
j j j j j j j j j j
d weight before lifting.
j j j
11. What is the main purpose of crane counterweights?
j j j j j j j
a) To increase boom angle capacity
j j j j
b) To balance the crane against overturning
j j j j j
c) To reduce wire rope tension
j j j j
j j j j j
estions And Correct Answers (Verified Answe
j j j j j
rs) Plus Rationales 2026|2027 Q&A | Instant
j j j j j j j
Download Pdf j
1. What is the primary purpose of a crane load chart?
j j j j j j j j j j
a) To show the crane’s engine specifications
j j j j j
b) To indicate the crane’s counterweight size
j j j j j
c) To determine the crane’s lifting capacities at various co
j j j j j j j j
nfigurations
d) To calculate wire rope strength
j j j j
The load chart provides the crane operator with lifting capacities at differe
j j j j j j j j j j j
nt boom lengths, radii, and configurations to ensure safe operation.
j j j j j j j j j
2. What does the term "working radius" mean in crane operation?
j j j j j j j j j
a) The distance between the crane cab and the ground
j j j j j j j j
b) The horizontal distance from the center of rotation to the center of t
j j j j j j j j j j j j
he load j
, c) The distance the boom can extend vertically
j j j j j j
d) The counterweight’s effective range
j j j
Working radius is measured horizontally from the crane’s center of rotatio
j j j j j j j j j j
n to the load’s center, and it directly affects lifting capacity.
j j j j j j j j j j
3. When operating a mobile crane on outriggers, the crane’s capacity is bas
j j j j j j j j j j j
ed on:
j
a) The ground condition only
j j j
b) The counterweight size only
j j j
c) The crane’s load chart for “on outriggers” configuration
j j j j j j j
d) The boom angle only j j j
Capacity is determined from the manufacturer’s load chart specific to the o
j j j j j j j j j j j
utrigger setup. j
4. Which of the following ground conditions is most dangerous for crane set
j j j j j j j j j j j
up?
a) Compacted gravel j
b) Concrete pad j
c) Soft or uncompacted soil j j j
d) Asphalt over crushed stone j j j
Soft or uncompacted soil may not support the crane’s weight, leading to ins
j j j j j j j j j j j j
tability and possible overturning.
j j j
5. What does "D/d ratio" refer to in crane operations?
j j j j j j j j
a) The drum size to load size ratio
j j j j j j
b) The ratio of the diameter of the sheave to the diameter of the
j j j j j j j j j j j j
, rope
c) The load chart ratio of duty cycle to design
j j j j j j j j
d) The outrigger span to crane height ratio
j j j j j j
The D/d ratio ensures wire rope bends around sheaves of sufficient size to p
j j j j j j j j j j j j j
revent rope fatigue and damage. j j j j
6. What is the purpose of a boom angle indicator?
j j j j j j j j
a) To measure wind speed
j j j
b) To show the angle of the boom relative to the ground
j j j j j j j j j j
c) To determine counterweight requirements
j j j
d) To calculate load radius automatically
j j j j
A boom angle indicator allows the operator to determine the radius, which
j j j j j j j j j j j
is essential for safe lifting based on the load chart.
j j j j j j j j j j
7. OSHA requires a signal person when:
j j j j j
a) The load is under 500 lbs j j j j j
b) The operator has a clear line of sight
j j j j j j j
c) The operator’s view of the load or path is obstructed
j j j j j j j j j
d) The lift is less than 10 feet j j j j j j
A signal person is required when the operator cannot see the load or path, e
j j j j j j j j j j j j j j
nsuring communication for safe movement. j j j j
8. Which hand signal universally means "emergency stop"?
j j j j j j
a) Arm extended forward with palm down, moving up and down
j j j j j j j j j
b) Arm extended with palm down, moved rapidly back and forth
j j j j j j j j j
c) Arm extended upward, pointing with one finger
j j j j j j
, d) Arm circling overhead j j
The emergency stop signal is standardized as an arm extended with palm d
j j j j j j j j j j j j
own, moved rapidly side to side.
j j j j j
9. What is the function of the anti-two-block device?
j j j j j j j
a) To prevent load line from unspooling
j j j j j
b) To prevent the hook block from contacting the boom tip
j j j j j j j j j
c) To stop the crane from exceeding load chart capacity
j j j j j j j j
d) To measure boom deflection
j j j
The anti-two-
j
block device prevents dangerous contact between the hook block and boo
j j j j j j j j j j
m tip, which could break the rope.
j j j j j j
10. What is the best method to verify the weight of a load before liftin
j j j j j j j j j j j j j
g?
a) Estimate based on appearance j j j
b) Check shipping papers, drawings, or manufacturer’s data
j j j j j j
c) Ask the rigger j j
d) Perform a test lift j j j
Using official documentation is the most accurate method for verifying loa
j j j j j j j j j j
d weight before lifting.
j j j
11. What is the main purpose of crane counterweights?
j j j j j j j
a) To increase boom angle capacity
j j j j
b) To balance the crane against overturning
j j j j j
c) To reduce wire rope tension
j j j j
