NACE CIP 1 CBT Exam Practice Exam with Questions and Answers – 100% Solved
(Also known as 'fisheyes' or 'crawling') is the term for surface breaks in the film that reveal the
substrate. It is often a result of grease or oil contamination on the substrate. - ✔✔✔-Cissing
A barrier coating interrupts the of the electrochemical cell? - ✔✔✔-electrolyte
A decrease in temperature will generally cause the corrosrion rate to? - ✔✔✔-Decrease
A magnetic pull off type gauge is a good choice when: - ✔✔✔-When an intrinsically safe tool is
required.
A NACE Coating Inspector is permitted to transport coating material when: - ✔✔✔-The
Inspector should never transport coating material.
A pre job conference is useful for discussions on which of the following? - ✔✔✔-Safety,
Cleaning, Application and Schedule.
A pre job conference should be held: - ✔✔✔-after bids have been submitted and contracts
signed.
A proper coating specification should contain information regarding which of the following? -
✔✔✔-Surface preparation standards, safety and locations to be coated.
A successful coating Inspector must be able to: - ✔✔✔-Look for problems and issues during
application.
A typical daily report should include which of the following? - ✔✔✔-Description of manpower
and equipment used by the contractor, explanation of work stoppages and list of environmental
conditions.
,NACE CIP 1 CBT Exam Practice Exam with Questions and Answers – 100% Solved
A well written specification requires a surface profile depth defined as? - ✔✔✔-A range of
measurements.
According to ASTM D 4417 Method B 2014 when taking measurements using a profile gauge, at
each location you should make? - ✔✔✔-10 readings per location, recording the maximum
value. Determine mean (average) for all maximum valises the reported profile.
According to NACE No.4/SSPC SP7, mill scale, rust, and paint are considered highly adherent if
they cannot be removed by? - ✔✔✔-Lifting with a dull putty knife.
According to NACE SP0188, the wetted sponge is moved at a maximum rate of? - ✔✔✔-1 linear
foot per second (30cm)
According to SSPC PA 2 a spot measurement it: - ✔✔✔-The average of gauge readings taken in a
4cm (1.5inch) circle.
According to the NACE attestation, when is it OK to accept a gift from a contractor? - ✔✔✔-
Never acceptable.
Adding an incorrect solvent to a coating may cause? - ✔✔✔-Non drying and non curing.
After a cold night, you find that the epoxy amine midcoast applied the day before has blushed.
The optimum (best) resolution when amine blush is found is to? - ✔✔✔-Consult the coating
manufacture.
Amine blush is likely to occur with which type of coating? - ✔✔✔-Epoxy
An exposed area of the substrate or previous coat of a conductive material, often caused by
poor application technique is called: - ✔✔✔-Holiday
, NACE CIP 1 CBT Exam Practice Exam with Questions and Answers – 100% Solved
An inspector should change position when: - ✔✔✔-The inspector is convinced by verifiable
facts.
An Inspectors personal log book should contain: - ✔✔✔-No comments regarding the
application team.
Approximately 75% of premature coating failures are caused by? - ✔✔✔-Inadequate or
improper surface preparation.
As a NACE Coating Inspector your responsibility with respect to safety is to: - ✔✔✔-Act in
accordance with the site safety requirements and set an example.
As an inspector headed to the joist for the first time, where would you always find instruction
regarding appropriate types of Personal Protective Equipment(PPE). - ✔✔✔-Safety Data
Sheet(SDS, previously called MSDS
As in Inspector on a bride painting project, prior to abrasive blasting,which blasting safety items
would you expect to see? - ✔✔✔-Deadman valve, Connections wired/clipped and Supplied air
hood.
As the Inspector called in to verify a blast, you find steel which has scattered highly adherent
rust remaining on less than 5% of the unit area. Which standard has been achieved? - ✔✔✔-
NACE No. 2/SSPC SP 10
ASTM Standards are applicable: - ✔✔✔-When specified.
Based on the galvanic series presented in the NACE CIP Level 1 Manual, which three materials
are commonly used as galvanic anodes for carbon steel? - ✔✔✔-Zinc, aluminum and
magnesium.
(Also known as 'fisheyes' or 'crawling') is the term for surface breaks in the film that reveal the
substrate. It is often a result of grease or oil contamination on the substrate. - ✔✔✔-Cissing
A barrier coating interrupts the of the electrochemical cell? - ✔✔✔-electrolyte
A decrease in temperature will generally cause the corrosrion rate to? - ✔✔✔-Decrease
A magnetic pull off type gauge is a good choice when: - ✔✔✔-When an intrinsically safe tool is
required.
A NACE Coating Inspector is permitted to transport coating material when: - ✔✔✔-The
Inspector should never transport coating material.
A pre job conference is useful for discussions on which of the following? - ✔✔✔-Safety,
Cleaning, Application and Schedule.
A pre job conference should be held: - ✔✔✔-after bids have been submitted and contracts
signed.
A proper coating specification should contain information regarding which of the following? -
✔✔✔-Surface preparation standards, safety and locations to be coated.
A successful coating Inspector must be able to: - ✔✔✔-Look for problems and issues during
application.
A typical daily report should include which of the following? - ✔✔✔-Description of manpower
and equipment used by the contractor, explanation of work stoppages and list of environmental
conditions.
,NACE CIP 1 CBT Exam Practice Exam with Questions and Answers – 100% Solved
A well written specification requires a surface profile depth defined as? - ✔✔✔-A range of
measurements.
According to ASTM D 4417 Method B 2014 when taking measurements using a profile gauge, at
each location you should make? - ✔✔✔-10 readings per location, recording the maximum
value. Determine mean (average) for all maximum valises the reported profile.
According to NACE No.4/SSPC SP7, mill scale, rust, and paint are considered highly adherent if
they cannot be removed by? - ✔✔✔-Lifting with a dull putty knife.
According to NACE SP0188, the wetted sponge is moved at a maximum rate of? - ✔✔✔-1 linear
foot per second (30cm)
According to SSPC PA 2 a spot measurement it: - ✔✔✔-The average of gauge readings taken in a
4cm (1.5inch) circle.
According to the NACE attestation, when is it OK to accept a gift from a contractor? - ✔✔✔-
Never acceptable.
Adding an incorrect solvent to a coating may cause? - ✔✔✔-Non drying and non curing.
After a cold night, you find that the epoxy amine midcoast applied the day before has blushed.
The optimum (best) resolution when amine blush is found is to? - ✔✔✔-Consult the coating
manufacture.
Amine blush is likely to occur with which type of coating? - ✔✔✔-Epoxy
An exposed area of the substrate or previous coat of a conductive material, often caused by
poor application technique is called: - ✔✔✔-Holiday
, NACE CIP 1 CBT Exam Practice Exam with Questions and Answers – 100% Solved
An inspector should change position when: - ✔✔✔-The inspector is convinced by verifiable
facts.
An Inspectors personal log book should contain: - ✔✔✔-No comments regarding the
application team.
Approximately 75% of premature coating failures are caused by? - ✔✔✔-Inadequate or
improper surface preparation.
As a NACE Coating Inspector your responsibility with respect to safety is to: - ✔✔✔-Act in
accordance with the site safety requirements and set an example.
As an inspector headed to the joist for the first time, where would you always find instruction
regarding appropriate types of Personal Protective Equipment(PPE). - ✔✔✔-Safety Data
Sheet(SDS, previously called MSDS
As in Inspector on a bride painting project, prior to abrasive blasting,which blasting safety items
would you expect to see? - ✔✔✔-Deadman valve, Connections wired/clipped and Supplied air
hood.
As the Inspector called in to verify a blast, you find steel which has scattered highly adherent
rust remaining on less than 5% of the unit area. Which standard has been achieved? - ✔✔✔-
NACE No. 2/SSPC SP 10
ASTM Standards are applicable: - ✔✔✔-When specified.
Based on the galvanic series presented in the NACE CIP Level 1 Manual, which three materials
are commonly used as galvanic anodes for carbon steel? - ✔✔✔-Zinc, aluminum and
magnesium.
