NYC NYCHA Maintenance Worker Exam Practice Test Questions And Correct Newest Updated Practice Exam | 150 Actual Most Tested Questions Collections & Verified Detailed Answers | Tutor Verified Success Exam) Graded A+

NYC NYCHA Maintenance Worker Exam Practice
Test Questions And Correct Newest 2025- 2026
Updated Practice Exam | 150 Actual Most Tested
Questions Collections & Verified Detailed Answers
| Tutor Verified Success Exam) Graded A+
1. A maintenance worker is assigned to replace a faulty light switch in an
apartment. What is the FIRST step before beginning work
A. Remove the switch cover
B. Turn off power at the circuit breaker
C. Test the switch
D. Notify the tenant
Correct Answer: B ✓
Rationale: The primary safety procedure is to de-energize the circuit to
prevent electrical shock. Working on live circuits violates standard
electrical safety protocols.
2. Which tool is BEST suited for tightening a hex bolt
A. Flathead screwdriver
B. Adjustable wrench
C. Needle-nose pliers
D. Hammer
Correct Answer: B ✓
Rationale: An adjustable wrench is designed for gripping and turning
hexagonal fasteners, ensuring proper torque and preventing damage.
3. A leaking pipe under a sink is most commonly caused by
A. Electrical failure
B. Loose fittings or worn washers
C. High voltage
D. Broken tiles

, Correct Answer: B ✓
Rationale: Leaks are typically due to loose connections or degraded
washers, both common in plumbing systems.
4. What is the purpose of a GFCI outlet
A. Increase voltage
B. Reduce lighting
C. Protect against electrical shock
D. Improve wiring speed
Correct Answer: C ✓
Rationale: A Ground Fault Circuit Interrupter (GFCI) detects imbalance in
current and shuts off power to prevent shock hazards.
5. When using a ladder, it should be placed at what angle
A. 90 degrees
B. 45 degrees
C. 75 degrees
D. 30 degrees
Correct Answer: C ✓
Rationale: The 4-to-1 rule establishes a safe ladder angle of approximately
75 degrees for stability.
6. A clogged drain is best cleared first using
A. Hammer
B. Plunger
C. Paintbrush
D. Saw
Correct Answer: B ✓
Rationale: A plunger uses pressure and suction to remove simple
blockages without damaging pipes.
7. Which material is commonly used for water supply pipes in modern
buildings
A. Wood

, B. PVC or copper
C. Rubber only
D. Glass
Correct Answer: B ✓
Rationale: PVC and copper are standard due to durability, corrosion
resistance, and safety.
8. What does PPE stand for
A. Power Pipe Equipment
B. Personal Protective Equipment
C. Primary Power Entry
D. Public Property Equipment
Correct Answer: B ✓
Rationale: PPE includes items like gloves and helmets used for worker
safety.
9. A circuit breaker trips repeatedly. What is the MOST likely cause
A. Too little current
B. Overloaded circuit
C. Proper operation
D. Clean wiring
Correct Answer: B ✓
Rationale: Frequent tripping indicates excess current draw, a sign of an
overloaded circuit.
10.Which of the following is a safe lifting practice
A. Bend at the waist
B. Keep load away from body
C. Lift with legs
D. Twist while lifting
Correct Answer: C ✓
Rationale: Proper lifting involves using leg muscles to reduce back injury
risk.

, 11.A tenant reports no heat in winter. What should be checked FIRST
A. Paint condition
B. Thermostat setting
C. Window locks
D. Floor tiles
Correct Answer: B ✓
Rationale: The thermostat controls heating systems and is the first
diagnostic step.
12.Which tool measures electrical voltage
A. Multimeter
B. Hammer
C. Wrench
D. Level
Correct Answer: A ✓
Rationale: A multimeter measures voltage, current, and resistance.
13.Mold growth is primarily caused by
A. Dry air
B. Excess moisture
C. Bright light
D. Clean surfaces
Correct Answer: B ✓
Rationale: Moisture accumulation promotes mold development, especially
in poorly ventilated areas.
14.What is the function of a fuse
A. Increase power
B. Store energy
C. Protect circuit from overload
D. Cool wires
Correct Answer: C ✓
Rationale: A fuse melts when current exceeds safe limits, preventing
damage or fire.