MILLWRIGHT LEVEL 1 UPDATED CORE 2026 QUESTIONS
AND ANSWERS SURE A+
✔✔The area of a rectangle is found by the formula ____. - ✔✔a=lw
✔✔When sketching hold the pencil _______. - ✔✔3/4 to 1
✔✔Anchor bolts that have been improperly installed usually have to be ___. - ✔✔Cut off
and replaced
✔✔Surface plates vary in size but are usually large blocks of precision- ground and
polished _____. - ✔✔Granite
✔✔When pneumatic gauges fail, they are usually _____. - ✔✔Replaced instead of
repaired
✔✔The frame and support of a belt conveyor is called the conveyor ____. - ✔✔Bed
✔✔A beam clamp should be replaced if it's jaws have been opened more than
_____percent of it's normal opening. - ✔✔15
✔✔Generally, the higher the quality of the steel fastener, the _____ on the head. -
✔✔Greater number of marks
✔✔A easy-out is used to ______. - ✔✔Remove screws and bolts
✔✔To determine clearance between surfaces, _____ is used. - ✔✔Thickness gauge
stock
✔✔Pneumatic blower conveyors use a continuous mass of flowing air to move the
product, which is usually dry, granular pellets or ______. - ✔✔Powder
✔✔When removing a bearing from a housing, position the bearing so that pressure is
only exerted on the ______. - ✔✔Outer race
✔✔Impulse turbines are also known as ______ turbines. - ✔✔Constant-pressure
✔✔With an induction heater, a bearing is heated _______. - ✔✔From the inside out
✔✔The major energy loss between gears is from ______. - ✔✔Friction
✔✔Many round objects take on the appearance of a ________ when pictured at a
certain angle. - ✔✔Ellipse
, ✔✔A double back to back seal is classified as _______. - ✔✔Multiple sealing unit
✔✔The type of V belt that is used on multiple sheave drives that cause the belt to have
reverse bends is the ______ belt. - ✔✔Double-angle
✔✔The safest way to store compressed gas cylinders is ______. - ✔✔Upright
✔✔Slotted nuts are prevented from working loose by use of a ______. - ✔✔cotter pin
✔✔The most likely spot for the air to enter a pump is around the ______. - ✔✔Packing
✔✔Instead of using time schedules to define equipment repairs and predict failures,
PDM uses ______\. - ✔✔Testing
✔✔The main purpose of a horizontal bandsaw is to ______. - ✔✔Cut pieces to length
✔✔An optical level consist of telescopic sight attached to a _______. - ✔✔Sensitive
spirit level
✔✔In piston pumps, the pumping element is a piston that moves _____ the pump
chamber. - ✔✔Back and forth in
✔✔A micrometer is used to take precise measurements of_____. - ✔✔Non moving
parts
✔✔Troubleshooting is a matter of identifying a problem and then determining the
possible ____. - ✔✔Causes
✔✔When preparing to couple and align the machines, the coupling gap should be set
according to the ______. - ✔✔Coupling manufacturers specifications
✔✔When removing the rotor, hook the sling ______ to rotor discs. - ✔✔Either outside or
between
✔✔The value of each line on the vernier scale of a U.S. standard vernier caliper is
______ inch. - ✔✔0.001
✔✔The throw out lever on a threading machine chuck is used to ______. - ✔✔Bring the
dies against the pipe or move them out of contact
✔✔When hangers are correctly placed and set, no _____is carried by the STAT. -
✔✔Pipe weight
AND ANSWERS SURE A+
✔✔The area of a rectangle is found by the formula ____. - ✔✔a=lw
✔✔When sketching hold the pencil _______. - ✔✔3/4 to 1
✔✔Anchor bolts that have been improperly installed usually have to be ___. - ✔✔Cut off
and replaced
✔✔Surface plates vary in size but are usually large blocks of precision- ground and
polished _____. - ✔✔Granite
✔✔When pneumatic gauges fail, they are usually _____. - ✔✔Replaced instead of
repaired
✔✔The frame and support of a belt conveyor is called the conveyor ____. - ✔✔Bed
✔✔A beam clamp should be replaced if it's jaws have been opened more than
_____percent of it's normal opening. - ✔✔15
✔✔Generally, the higher the quality of the steel fastener, the _____ on the head. -
✔✔Greater number of marks
✔✔A easy-out is used to ______. - ✔✔Remove screws and bolts
✔✔To determine clearance between surfaces, _____ is used. - ✔✔Thickness gauge
stock
✔✔Pneumatic blower conveyors use a continuous mass of flowing air to move the
product, which is usually dry, granular pellets or ______. - ✔✔Powder
✔✔When removing a bearing from a housing, position the bearing so that pressure is
only exerted on the ______. - ✔✔Outer race
✔✔Impulse turbines are also known as ______ turbines. - ✔✔Constant-pressure
✔✔With an induction heater, a bearing is heated _______. - ✔✔From the inside out
✔✔The major energy loss between gears is from ______. - ✔✔Friction
✔✔Many round objects take on the appearance of a ________ when pictured at a
certain angle. - ✔✔Ellipse
, ✔✔A double back to back seal is classified as _______. - ✔✔Multiple sealing unit
✔✔The type of V belt that is used on multiple sheave drives that cause the belt to have
reverse bends is the ______ belt. - ✔✔Double-angle
✔✔The safest way to store compressed gas cylinders is ______. - ✔✔Upright
✔✔Slotted nuts are prevented from working loose by use of a ______. - ✔✔cotter pin
✔✔The most likely spot for the air to enter a pump is around the ______. - ✔✔Packing
✔✔Instead of using time schedules to define equipment repairs and predict failures,
PDM uses ______\. - ✔✔Testing
✔✔The main purpose of a horizontal bandsaw is to ______. - ✔✔Cut pieces to length
✔✔An optical level consist of telescopic sight attached to a _______. - ✔✔Sensitive
spirit level
✔✔In piston pumps, the pumping element is a piston that moves _____ the pump
chamber. - ✔✔Back and forth in
✔✔A micrometer is used to take precise measurements of_____. - ✔✔Non moving
parts
✔✔Troubleshooting is a matter of identifying a problem and then determining the
possible ____. - ✔✔Causes
✔✔When preparing to couple and align the machines, the coupling gap should be set
according to the ______. - ✔✔Coupling manufacturers specifications
✔✔When removing the rotor, hook the sling ______ to rotor discs. - ✔✔Either outside or
between
✔✔The value of each line on the vernier scale of a U.S. standard vernier caliper is
______ inch. - ✔✔0.001
✔✔The throw out lever on a threading machine chuck is used to ______. - ✔✔Bring the
dies against the pipe or move them out of contact
✔✔When hangers are correctly placed and set, no _____is carried by the STAT. -
✔✔Pipe weight
