P1 Exam - IRC (Residential Plumbing IRC)
Practice Questions AND Answers | latest update
Save
Practice questions for this set
Learn 1/7 Study with Learn
7 feet (P3103.1.2)
Choose an answer
In general, fuel-fired appliances are permitted to be located in which one of the
1
following spaces?
Where a roof is to be used for assembly, such as a promenade or observation deck, a
2
vent extension shall terminate a minimum of __________ above the roof.
In general, underground gas piping shall be installed a minimum depth of _______ below
3
grade.
Assume that a fuel-gas appliance requires a minimum clearance without protection of 9
inches from the sides and back to combustible material. If 0.024 sheet metal with a
4
ventilated air space is used as protection, the minimum clearance may be reduced to
______.
, Don't know?
Terms in this set (140)
In general, fuel-fired appliances are Garages (G2406.2)
permitted to be located in which one
of the following spaces?
Where located in hazardous 18 inches (G2408.2)
locations, fuel-gas equipment and
appliances having an ignition source
shall be elevated such that the
ignition source is located a minimum
of _____ above the floor.
Unless protected from motor vehicle 72 inches (G2408.3)
damage, fuel-gas appliances
located in private garages shall be
installed with a minimum clearance
of _____ above the floor.
Assume that a fuel-gas appliance 24 inches (Table G2409.2)
requires a minimum clearance
without protection for 36 inches
above the appliance to combustible
material. If ½-inch thick insulation
board over 1-inch glass fiber batts is
used as protection, the minimum
clearance may be reduced to ______.
, Assume that a fuel-gas appliance 3 inches (Table G2409.2)
requires a minimum clearance
without protection of 9 inches from
the sides and back to combustible
material. If 0.024 sheet metal with a
ventilated air space is used as
protection, the minimum clearance
may be reduced to ______.
For other than steel pipe and CSST, 5 feet (G2412.5)
exposed gas piping shall be
identified by a yellow label marked
'Gas' spaced at maximum intervals of
_____ unless in the same room as the
appliance served.
Unless special conditions are met, 5 psig (G2413.7)
the maximum design operating
pressure for gas piping systems
located inside buildings shall be ______.
LP-gas systems designed to operate -5 F (G2413.7.1)
below _______ shall be designed to
either accommodate liquid LP-gas or
prevent LP-gas vapor from
condensing into a liquid.
Copper tubing to be used with Type K or Type L (G2414.4.3)
gasses shall comply with standard
______ of ASTM B88 or ASTM B280.
Practice Questions AND Answers | latest update
Save
Practice questions for this set
Learn 1/7 Study with Learn
7 feet (P3103.1.2)
Choose an answer
In general, fuel-fired appliances are permitted to be located in which one of the
1
following spaces?
Where a roof is to be used for assembly, such as a promenade or observation deck, a
2
vent extension shall terminate a minimum of __________ above the roof.
In general, underground gas piping shall be installed a minimum depth of _______ below
3
grade.
Assume that a fuel-gas appliance requires a minimum clearance without protection of 9
inches from the sides and back to combustible material. If 0.024 sheet metal with a
4
ventilated air space is used as protection, the minimum clearance may be reduced to
______.
, Don't know?
Terms in this set (140)
In general, fuel-fired appliances are Garages (G2406.2)
permitted to be located in which one
of the following spaces?
Where located in hazardous 18 inches (G2408.2)
locations, fuel-gas equipment and
appliances having an ignition source
shall be elevated such that the
ignition source is located a minimum
of _____ above the floor.
Unless protected from motor vehicle 72 inches (G2408.3)
damage, fuel-gas appliances
located in private garages shall be
installed with a minimum clearance
of _____ above the floor.
Assume that a fuel-gas appliance 24 inches (Table G2409.2)
requires a minimum clearance
without protection for 36 inches
above the appliance to combustible
material. If ½-inch thick insulation
board over 1-inch glass fiber batts is
used as protection, the minimum
clearance may be reduced to ______.
, Assume that a fuel-gas appliance 3 inches (Table G2409.2)
requires a minimum clearance
without protection of 9 inches from
the sides and back to combustible
material. If 0.024 sheet metal with a
ventilated air space is used as
protection, the minimum clearance
may be reduced to ______.
For other than steel pipe and CSST, 5 feet (G2412.5)
exposed gas piping shall be
identified by a yellow label marked
'Gas' spaced at maximum intervals of
_____ unless in the same room as the
appliance served.
Unless special conditions are met, 5 psig (G2413.7)
the maximum design operating
pressure for gas piping systems
located inside buildings shall be ______.
LP-gas systems designed to operate -5 F (G2413.7.1)
below _______ shall be designed to
either accommodate liquid LP-gas or
prevent LP-gas vapor from
condensing into a liquid.
Copper tubing to be used with Type K or Type L (G2414.4.3)
gasses shall comply with standard
______ of ASTM B88 or ASTM B280.
