ALBERTA WELDING FIRST YEAR AIT COMPLETE LATEST FINAL EXAM UPDATED
FOR 2026-2027 ACTUAL QUESTIONS WITH 100% CERTIFIED, ELABORATED &
VERIFIED SOLUTIONS- TOP SCORE -ACE YOUR EXAMS
A Material Safety Data Sheet must be reviewed whenever new information becomes available
or at least how often?
every three years
What is the total number of hours of work experience, including technical training, required per
year in the Welder Apprenticeship Program?
1800
Voltage-sensing wire feeders set their speed according to: arc
voltage.
How much electrode stickout is recommended when using gas shielded FCAW with 1.2 mm
(0.045") wire?
10 mm to 19 mm (3/8" to 3/4")
One of the main functions of the contact tube is to: transfer
current to the electrode.
Flame propagation means the speed at which the fuel gas will travel
False
What height limitation is in place when using freestanding scaffolding?
For free standing scaffolds, the scaffold must not be taller than three (3) times its smallest
dimension in height
The best reference point for dimensioning on pressure vessels is the:
datum line
Which of the following is an abbreviation of a Non destructive test ?
UT
In common fabricating practice, there are how many basic joint types?
5
, Single "V" butt joints are used on material thicknesses of:
3/8" -1" (9.5 -25.4mm)
A small change in sling angle can drastically affect the:
sling load.
The power sources used for pulsed spray transfer are:
DC synergic, microprocessor-controlled.
Single "V" butt joints are used on material thicknesses of:
3/8" -1" (9.5 -25.4mm)
If you must apply force to a suspended load, always pull the load towards you.
When installing clips, the saddle side of the clip must be placed on the:
Live side of the wire
When balancing a No. 2 welding tip and the acetylene torch needle valve is fully open, the
acetylene regulator should be adjusted so that the flame blows away from the tip _______ inch.
(Oxygen needle valve is closed)
1/4
Which ferrous-based metals cannot be cut satisfactorily with an oxy-fuel cutting torch?
stainless
What is the total number of hours in the first period Welder Training Profile?
240
When starting a cut on plate, the preheat cones should be held:
about 3 mm (1/8") above the surface. What is the main
purpose of the contact tube? transfers the welding current to
the filler wire
A steamed vessel is safest to weld on when it is cooled down to room temperature .
False
FOR 2026-2027 ACTUAL QUESTIONS WITH 100% CERTIFIED, ELABORATED &
VERIFIED SOLUTIONS- TOP SCORE -ACE YOUR EXAMS
A Material Safety Data Sheet must be reviewed whenever new information becomes available
or at least how often?
every three years
What is the total number of hours of work experience, including technical training, required per
year in the Welder Apprenticeship Program?
1800
Voltage-sensing wire feeders set their speed according to: arc
voltage.
How much electrode stickout is recommended when using gas shielded FCAW with 1.2 mm
(0.045") wire?
10 mm to 19 mm (3/8" to 3/4")
One of the main functions of the contact tube is to: transfer
current to the electrode.
Flame propagation means the speed at which the fuel gas will travel
False
What height limitation is in place when using freestanding scaffolding?
For free standing scaffolds, the scaffold must not be taller than three (3) times its smallest
dimension in height
The best reference point for dimensioning on pressure vessels is the:
datum line
Which of the following is an abbreviation of a Non destructive test ?
UT
In common fabricating practice, there are how many basic joint types?
5
, Single "V" butt joints are used on material thicknesses of:
3/8" -1" (9.5 -25.4mm)
A small change in sling angle can drastically affect the:
sling load.
The power sources used for pulsed spray transfer are:
DC synergic, microprocessor-controlled.
Single "V" butt joints are used on material thicknesses of:
3/8" -1" (9.5 -25.4mm)
If you must apply force to a suspended load, always pull the load towards you.
When installing clips, the saddle side of the clip must be placed on the:
Live side of the wire
When balancing a No. 2 welding tip and the acetylene torch needle valve is fully open, the
acetylene regulator should be adjusted so that the flame blows away from the tip _______ inch.
(Oxygen needle valve is closed)
1/4
Which ferrous-based metals cannot be cut satisfactorily with an oxy-fuel cutting torch?
stainless
What is the total number of hours in the first period Welder Training Profile?
240
When starting a cut on plate, the preheat cones should be held:
about 3 mm (1/8") above the surface. What is the main
purpose of the contact tube? transfers the welding current to
the filler wire
A steamed vessel is safest to weld on when it is cooled down to room temperature .
False
