Arizona CR-7 Carpentry Contractor
Exam Practice Questions And Correct
Answers (Verified Answers) Plus
Rationale 2026 Q&A| Instant Download
Pdf
1. What is the primary purpose of a footing in a structural foundation?
A. To provide insulation
B. To resist lateral soil pressure
C. To distribute structural loads to the soil
D. To act as a vapor barrier
Rationale: Footings spread the building’s structural loads over a larger
area of soil to prevent settlement or structural failure.
2. In roof framing, the ridge board is installed:
A. At the eave line
B. At the highest point where rafters meet
C. Under the sheathing
D. Along the wall plate
Rationale: The ridge board serves as the uppermost horizontal
member where opposing rafters connect.
3. What type of joint connects two pieces of lumber end-to-end in a
straight line?
, A. Mortise and tenon
B. Dovetail
C. Lap
D. Scarf
Rationale: A scarf joint joins two lengthwise pieces of lumber to form a
continuous member.
4. Which document establishes the legal relationship between an owner
and contractor?
A. Change order
B. Contract agreement
C. Submittal
D. Request for information
Rationale: The contract agreement defines roles, responsibilities, and
terms between owner and contractor.
5. The IRC requirement for the minimum stair tread depth is:
A. 8 inches
B. 10 inches
C. 12 inches
D. 6 inches
Rationale: Standard building code requires at least 10-inch stair treads
for safety and usability.
6. Which fastener is best for outdoor deck construction due to corrosion
resistance?
A. Plain steel nail
B. Aluminum screw
C. Hot-dip galvanized screw
D. Brass tack
Rationale: Galvanized fasteners resist corrosion in exterior applications
like decks.
, 7. A plumb line is used to measure:
A. Length
B. Vertical alignment
C. Horizontal level
D. Angle degree
Rationale: A plumb line determines true vertical for accurate framing.
8. What does ‘clear span’ refer to in floor joist design?
A. Width between walls
B. Distance between supports
C. Total building length
D. Beam depth
Rationale: Clear span is the unsupported distance a joist or beam must
carry loads.
9. A wall that supports structural loads is called a:
A. Partition wall
B. Load-bearing wall
C. Curtain wall
D. Freestanding wall
Rationale: Load-bearing walls transfer weight from upper floors and
roof to the foundation.
10. Which hazard requires a Safety Data Sheet (SDS) on a job site?
A. Electrical tools
B. Noise
C. Chemical products
D. Heavy equipment
Rationale: SDS documents hazards of chemicals and required
protective measures.
11. The slope of a standard residential roof can be expressed as:
A. Percent grade
Exam Practice Questions And Correct
Answers (Verified Answers) Plus
Rationale 2026 Q&A| Instant Download
1. What is the primary purpose of a footing in a structural foundation?
A. To provide insulation
B. To resist lateral soil pressure
C. To distribute structural loads to the soil
D. To act as a vapor barrier
Rationale: Footings spread the building’s structural loads over a larger
area of soil to prevent settlement or structural failure.
2. In roof framing, the ridge board is installed:
A. At the eave line
B. At the highest point where rafters meet
C. Under the sheathing
D. Along the wall plate
Rationale: The ridge board serves as the uppermost horizontal
member where opposing rafters connect.
3. What type of joint connects two pieces of lumber end-to-end in a
straight line?
, A. Mortise and tenon
B. Dovetail
C. Lap
D. Scarf
Rationale: A scarf joint joins two lengthwise pieces of lumber to form a
continuous member.
4. Which document establishes the legal relationship between an owner
and contractor?
A. Change order
B. Contract agreement
C. Submittal
D. Request for information
Rationale: The contract agreement defines roles, responsibilities, and
terms between owner and contractor.
5. The IRC requirement for the minimum stair tread depth is:
A. 8 inches
B. 10 inches
C. 12 inches
D. 6 inches
Rationale: Standard building code requires at least 10-inch stair treads
for safety and usability.
6. Which fastener is best for outdoor deck construction due to corrosion
resistance?
A. Plain steel nail
B. Aluminum screw
C. Hot-dip galvanized screw
D. Brass tack
Rationale: Galvanized fasteners resist corrosion in exterior applications
like decks.
, 7. A plumb line is used to measure:
A. Length
B. Vertical alignment
C. Horizontal level
D. Angle degree
Rationale: A plumb line determines true vertical for accurate framing.
8. What does ‘clear span’ refer to in floor joist design?
A. Width between walls
B. Distance between supports
C. Total building length
D. Beam depth
Rationale: Clear span is the unsupported distance a joist or beam must
carry loads.
9. A wall that supports structural loads is called a:
A. Partition wall
B. Load-bearing wall
C. Curtain wall
D. Freestanding wall
Rationale: Load-bearing walls transfer weight from upper floors and
roof to the foundation.
10. Which hazard requires a Safety Data Sheet (SDS) on a job site?
A. Electrical tools
B. Noise
C. Chemical products
D. Heavy equipment
Rationale: SDS documents hazards of chemicals and required
protective measures.
11. The slope of a standard residential roof can be expressed as:
A. Percent grade
