1
Michigan State Brakes Certification Exam |
Correct Questions and Answers | Guaranteed
Pass | New
Most 1995 & newer vehicles use which of the following types of
wheels bearings on non-drive wheel? - Correct Answer✔✔-Sealed
non-serviceable
to test a vacuum power brake booster in the vehicle, you should pump
the brake pedal at least 4 times, hold the brake pedal depressed, and
start the engine. the brake pedal should: - Correct Answer✔✔-drop
slightly and remain firm
You are installing a set of brake shoe linings that are not the same
length. Traditionally, the primary shoe lining is: - Correct
Answer✔✔-Smaller and goes towards the front of the car.
A cracked or torn vacuum diaphragm in a brake power booster would
most likely cause: - Correct Answer✔✔-a hard pedal feel requiring
very high pedal effort to stop
A mechanic finds gear lube inside both rear brake drums on a rear
wheel drive vehicle. What is the most likely cause of this problem? -
Correct Answer✔✔-A plugged axle
Which of the following incorrect service procedures will cause brake
lock-up? - Correct Answer✔✔-master cylinder push rod adjusted too
long
Which of the following describes the proper way to depressurized an
ABS system? - Correct Answer✔✔-Pump the brake pedal at least 25
times (or more, depending on the manufacturer's recommendation)
with the ignition off.
, 2
The rear brakes are dragging after having new linings installed and
the drums machined. the most likely cause is the: - Correct
Answer✔✔-technician use the parking brake to adjust shoes and the
cable is stuck
When turning brake drums: - Correct Answer✔✔-use a dampening
strap to reduce chatter
Which of the following is NOT a necessary drum brake
measurement? - Correct Answer✔✔-run-out
On a 3-channel system, which wheels are on the same circuit? -
Correct Answer✔✔-both rear wheels
One way to test an ABS wheel speed signal is to use _____ on your
digital multimeter. - Correct Answer✔✔-AC volts
The key input for the ABS control module comes from the: - Correct
Answer✔✔-wheel speed sensors
ABS speed sensor and sensor rings: - Correct Answer✔✔-should not
be hammered or tapped on and should always be replaced as a
matched set
Flexible brake hoses should be replaced: - Correct Answer✔✔-when
dampness is evident on the hose
Which of the following should be used to check for rotor thickness
variation: - Correct Answer✔✔-Micrometer
After rebuilding a master cylinder, the rod between the master
cylinder and booster should be: - Correct Answer✔✔-adjusted
properly
Upon inspecting brake fluid condition, the technician observes the
diaphragm in the master cylinder cup is swollen. Which of the
Michigan State Brakes Certification Exam |
Correct Questions and Answers | Guaranteed
Pass | New
Most 1995 & newer vehicles use which of the following types of
wheels bearings on non-drive wheel? - Correct Answer✔✔-Sealed
non-serviceable
to test a vacuum power brake booster in the vehicle, you should pump
the brake pedal at least 4 times, hold the brake pedal depressed, and
start the engine. the brake pedal should: - Correct Answer✔✔-drop
slightly and remain firm
You are installing a set of brake shoe linings that are not the same
length. Traditionally, the primary shoe lining is: - Correct
Answer✔✔-Smaller and goes towards the front of the car.
A cracked or torn vacuum diaphragm in a brake power booster would
most likely cause: - Correct Answer✔✔-a hard pedal feel requiring
very high pedal effort to stop
A mechanic finds gear lube inside both rear brake drums on a rear
wheel drive vehicle. What is the most likely cause of this problem? -
Correct Answer✔✔-A plugged axle
Which of the following incorrect service procedures will cause brake
lock-up? - Correct Answer✔✔-master cylinder push rod adjusted too
long
Which of the following describes the proper way to depressurized an
ABS system? - Correct Answer✔✔-Pump the brake pedal at least 25
times (or more, depending on the manufacturer's recommendation)
with the ignition off.
, 2
The rear brakes are dragging after having new linings installed and
the drums machined. the most likely cause is the: - Correct
Answer✔✔-technician use the parking brake to adjust shoes and the
cable is stuck
When turning brake drums: - Correct Answer✔✔-use a dampening
strap to reduce chatter
Which of the following is NOT a necessary drum brake
measurement? - Correct Answer✔✔-run-out
On a 3-channel system, which wheels are on the same circuit? -
Correct Answer✔✔-both rear wheels
One way to test an ABS wheel speed signal is to use _____ on your
digital multimeter. - Correct Answer✔✔-AC volts
The key input for the ABS control module comes from the: - Correct
Answer✔✔-wheel speed sensors
ABS speed sensor and sensor rings: - Correct Answer✔✔-should not
be hammered or tapped on and should always be replaced as a
matched set
Flexible brake hoses should be replaced: - Correct Answer✔✔-when
dampness is evident on the hose
Which of the following should be used to check for rotor thickness
variation: - Correct Answer✔✔-Micrometer
After rebuilding a master cylinder, the rod between the master
cylinder and booster should be: - Correct Answer✔✔-adjusted
properly
Upon inspecting brake fluid condition, the technician observes the
diaphragm in the master cylinder cup is swollen. Which of the
