78. What weighing system is designed to provide weight data and compute the center
of gravity of aircraft?
Give this one a try later!
The Mobile Electronic Weighing System (MEWS)
37. When are block diagrams used?
Give this one a try later!
To illustrate a system, such as the nosewheel steering system, Each
component is represented by a block, with the name near that block.
,113. How often should all slings be examined and lubricated?
Give this one a try later!
Once a month in accordance with NAVAIR 17-1-114
63. What are the two most common types of grease guns in use?
Give this one a try later!
(1)The lever and (2)The one-handed lever guns
26. When is the word SHOULD used when referring to a safety hazard procedure?
Give this one a try later!
Only when application of a procedure is recommended
41. What are the two classes of diagrams you will be concerned with in gaining a
complete knowledge of a specific system?
Give this one a try later!
The schematic and installation diagrams.
,84. Spirit levels used for levelling aircraft should be of what type?
Give this one a try later!
A machinists' bench type of firs-class quality
39. When are orthographic drawings used?
Give this one a try later!
To show details of parts, components, and other objects, and are primarily
used by the manufacturer of the object.
32. What are dimension lines?
Give this one a try later!
Thin lines terminated with arrowheads at each end, used to used to indicate
distance measured.
102. What types of slings do not contain flexible components and are used for lifting
aircraft subassemblies?
Give this one a try later!
, Structural steel or aluminum
11. Where should defective tools received from supply be reported?
Give this one a try later!
The Fleet Material Support Office (FLEMATSUPPO) via CAT II Quality
Deficiency Reports (QDRs).
55. When you conduct a final operational check, how many times must the affected
system be actuated?
Give this one a try later!
A minimum of five times, or until a thorough check has been made to
determine that its operation and adjustments are satisfactory
73. What manual are the requirements, procedures, and responsibilities for aircraft
weight and balance control defined in?
Give this one a try later!
USN Aircraft Weight and Balance Control, NAVAIR 01-1B-50
135. What does the rate of descent of a jack depend?
of gravity of aircraft?
Give this one a try later!
The Mobile Electronic Weighing System (MEWS)
37. When are block diagrams used?
Give this one a try later!
To illustrate a system, such as the nosewheel steering system, Each
component is represented by a block, with the name near that block.
,113. How often should all slings be examined and lubricated?
Give this one a try later!
Once a month in accordance with NAVAIR 17-1-114
63. What are the two most common types of grease guns in use?
Give this one a try later!
(1)The lever and (2)The one-handed lever guns
26. When is the word SHOULD used when referring to a safety hazard procedure?
Give this one a try later!
Only when application of a procedure is recommended
41. What are the two classes of diagrams you will be concerned with in gaining a
complete knowledge of a specific system?
Give this one a try later!
The schematic and installation diagrams.
,84. Spirit levels used for levelling aircraft should be of what type?
Give this one a try later!
A machinists' bench type of firs-class quality
39. When are orthographic drawings used?
Give this one a try later!
To show details of parts, components, and other objects, and are primarily
used by the manufacturer of the object.
32. What are dimension lines?
Give this one a try later!
Thin lines terminated with arrowheads at each end, used to used to indicate
distance measured.
102. What types of slings do not contain flexible components and are used for lifting
aircraft subassemblies?
Give this one a try later!
, Structural steel or aluminum
11. Where should defective tools received from supply be reported?
Give this one a try later!
The Fleet Material Support Office (FLEMATSUPPO) via CAT II Quality
Deficiency Reports (QDRs).
55. When you conduct a final operational check, how many times must the affected
system be actuated?
Give this one a try later!
A minimum of five times, or until a thorough check has been made to
determine that its operation and adjustments are satisfactory
73. What manual are the requirements, procedures, and responsibilities for aircraft
weight and balance control defined in?
Give this one a try later!
USN Aircraft Weight and Balance Control, NAVAIR 01-1B-50
135. What does the rate of descent of a jack depend?
