Intermodal Dry Cargo CNTR/CSC
Reinspection (Cert), INTERMODAL DRY
CARGO CNTR/CSC REINSPEC
UPDATED Study Guide QUESTIONS
AND CORRET ANSWSER
What is the primary reference used by inspectors to conduct CSC container
inspections? - CORRECT ANSWERS MIL-STD-3037
Which of the following containers allows for easier loading and unloading of
large bulky stock, such as bombs? - CORRECT ANSWERS Side-
Opening
Which container component is highlighted? - CORRECT ANSWERS
Threshold Plate
Which container component is highlighted? - CORRECT ANSWERS
Top End Rail
Which container component is highlighted? - CORRECT ANSWERS
Forklift Pockets
Which container component is highlighted? - CORRECT ANSWERS
Gooseneck tunnel
What must be displayed on both ends, both sides, and the top of a container? -
CORRECT ANSWERS ISO Identification Markings
, When inspecting containers, what tool would you use to inspect a container's
alignment? - CORRECT ANSWERS Measuring Tape
When inspecting containers, what tool is used to determine weld serviceability
and the severity of corrosion? - CORRECT ANSWERS Welder's
Hammer
When inspecting containers, what tool is used to move containers by lifting
them at the corner fittings? - CORRECT ANSWERS Container handler
Where do you find the container inspection checklist for a mobile facility? -
CORRECT ANSWERS MIL-STD-3037, Appendix A
Which statement is true? - CORRECT ANSWERS MIL-STD-3037 has
separate paragraphs that document IMDG and non-IMDG criteria.
What is the maximum allowable depth of a door header dent? Refer to MIL-
STD-3037, Section 4 as required. - CORRECT ANSWERS ¾" for
IMDG, 1-⅜" for general cargo
Select the appropriate defect classification for the following container defect:
Dent 3/16" deep on the road side panel.
Refer to MIL-STD-3037, Section 4 as required. - CORRECT ANSWERS
Minor
Refer to DA Form 2404 below. What is the appropriate entry for Item #5 in this
example? - CORRECT ANSWERS Unserviceable for IMDG and Non-
IDMG
According to the DD Form 2282 decal shown below, when was this container
last inspected? - CORRECT ANSWERS May 2018
Reinspection (Cert), INTERMODAL DRY
CARGO CNTR/CSC REINSPEC
UPDATED Study Guide QUESTIONS
AND CORRET ANSWSER
What is the primary reference used by inspectors to conduct CSC container
inspections? - CORRECT ANSWERS MIL-STD-3037
Which of the following containers allows for easier loading and unloading of
large bulky stock, such as bombs? - CORRECT ANSWERS Side-
Opening
Which container component is highlighted? - CORRECT ANSWERS
Threshold Plate
Which container component is highlighted? - CORRECT ANSWERS
Top End Rail
Which container component is highlighted? - CORRECT ANSWERS
Forklift Pockets
Which container component is highlighted? - CORRECT ANSWERS
Gooseneck tunnel
What must be displayed on both ends, both sides, and the top of a container? -
CORRECT ANSWERS ISO Identification Markings
, When inspecting containers, what tool would you use to inspect a container's
alignment? - CORRECT ANSWERS Measuring Tape
When inspecting containers, what tool is used to determine weld serviceability
and the severity of corrosion? - CORRECT ANSWERS Welder's
Hammer
When inspecting containers, what tool is used to move containers by lifting
them at the corner fittings? - CORRECT ANSWERS Container handler
Where do you find the container inspection checklist for a mobile facility? -
CORRECT ANSWERS MIL-STD-3037, Appendix A
Which statement is true? - CORRECT ANSWERS MIL-STD-3037 has
separate paragraphs that document IMDG and non-IMDG criteria.
What is the maximum allowable depth of a door header dent? Refer to MIL-
STD-3037, Section 4 as required. - CORRECT ANSWERS ¾" for
IMDG, 1-⅜" for general cargo
Select the appropriate defect classification for the following container defect:
Dent 3/16" deep on the road side panel.
Refer to MIL-STD-3037, Section 4 as required. - CORRECT ANSWERS
Minor
Refer to DA Form 2404 below. What is the appropriate entry for Item #5 in this
example? - CORRECT ANSWERS Unserviceable for IMDG and Non-
IDMG
According to the DD Form 2282 decal shown below, when was this container
last inspected? - CORRECT ANSWERS May 2018
