GLOBUS QUIZ EXAM PREP EXAMINATION
TEST FULL SOLUTION 2026 GUARANTEED TO
PASS.
⫸ COALITION AGX. The allograft spacer is available in three
footprints? Answer: True
⫸ COALITION AGX: After finding the correct footprint size on the
assembly press, the plate should slide down the gold track? Answer:
False
⫸ COALITION AGX: How many Nm does it take for the set screw
positioner, 2.0mm Hex to torque out? Answer: 0.3 Nm
⫸ COALITION AGX: What size plates do the gold midline holders
go with in the Standard Instrument set? Answer: 12x14
14x16
⫸ COALITION MIS: Anchors should be selected to match the
respective color-coordinated spacer? Answer: False
⫸ COALITION MIS: The spacer should always be implanted as far
posterior as possible so that the positive stop on the Double Anchor
Guide contacts the vertebrae? Answer: False
, ⫸ COALITION MIS. How can you ensure an anchor is correctly
loaded into the Double Barrel Anchor Guide? Answer: All of the
above
⫸ COALITION MIS Each anchor is to be incrementaliy impacted
one at a time, using fluoroscopy to monitor the advancement of each
Anchor? Answer: True
⫸ COALITION MIS: If an Anchor needs to be removed from the
spacer once implanted, what should you advice the surgeon before the
removal? Answer: All of the above
⫸ COALITION MIS: The Double Barrel Anchor Guide will not
disengage from the spacer. What can you advise the surgeon to do?
(Select all that apply) Answer: Confirm the Hex Driver is fully seated
into the Threaded Rod hex hole
Ensure both anchors are fully seated
Rotate Hex Driver counterclockwise while simultaneously
withdrawing the instrument, rocking left/right as needed
⫸ The torque on the CREO 5.5 system is? Answer: 5.5 Nm
⫸ CREO® Threaded will accommodate which rod diameter(s)?
Answer: 5.5 & 6.0
TEST FULL SOLUTION 2026 GUARANTEED TO
PASS.
⫸ COALITION AGX. The allograft spacer is available in three
footprints? Answer: True
⫸ COALITION AGX: After finding the correct footprint size on the
assembly press, the plate should slide down the gold track? Answer:
False
⫸ COALITION AGX: How many Nm does it take for the set screw
positioner, 2.0mm Hex to torque out? Answer: 0.3 Nm
⫸ COALITION AGX: What size plates do the gold midline holders
go with in the Standard Instrument set? Answer: 12x14
14x16
⫸ COALITION MIS: Anchors should be selected to match the
respective color-coordinated spacer? Answer: False
⫸ COALITION MIS: The spacer should always be implanted as far
posterior as possible so that the positive stop on the Double Anchor
Guide contacts the vertebrae? Answer: False
, ⫸ COALITION MIS. How can you ensure an anchor is correctly
loaded into the Double Barrel Anchor Guide? Answer: All of the
above
⫸ COALITION MIS Each anchor is to be incrementaliy impacted
one at a time, using fluoroscopy to monitor the advancement of each
Anchor? Answer: True
⫸ COALITION MIS: If an Anchor needs to be removed from the
spacer once implanted, what should you advice the surgeon before the
removal? Answer: All of the above
⫸ COALITION MIS: The Double Barrel Anchor Guide will not
disengage from the spacer. What can you advise the surgeon to do?
(Select all that apply) Answer: Confirm the Hex Driver is fully seated
into the Threaded Rod hex hole
Ensure both anchors are fully seated
Rotate Hex Driver counterclockwise while simultaneously
withdrawing the instrument, rocking left/right as needed
⫸ The torque on the CREO 5.5 system is? Answer: 5.5 Nm
⫸ CREO® Threaded will accommodate which rod diameter(s)?
Answer: 5.5 & 6.0
