Computer Applications I Questions With Complete
Solutions
Bidirectional Associative Property Correct Answers Ability to
ensure that if any modifications are made in a particular model
in one mode, the corresponding modifications are also reflected
in the same model in other modes.
Constraint Correct Answers Defines position and size of one
entity to another: parallel, same size, perpendicular, tangent.
Copy Correct Answers Paste with options >
✅Dependant Copy
• Fully dependant with options to vary
✅ Advanced reference configuration
Could you put the BOM table in the format instead of the
drawing file? If you could do this, what would be the benefits?
Correct Answers Yes you can put the BOM in the format. This
would allow you to position the table by picking a corner. It also
means that you don't need to set up the table for each drawing,
saving time.
Creo Parametric 3.0 Correct Answers 1. Allows you to
manipulate any solid model dynamically.
2. Calculates the mass properties directly from the created
geometry.
3. Enables the real-time rendering of solid models.
Design Intent Correct Answers Create the model using
dimensions and constraints that are used for fabrication and
, inspection. Also, build it so that changing a dimension value will
cause the model to grow or shrink accordingly, rather than turn
into a shape that was not intended. (Example: a symmetric
model should remain symmetric if a dimension value is
changed).
Dimension Correct Answers Measurement of one or more
entities.
Entity Correct Answers An element of geometry in a cross-
section: line, point, circle, conic, or coordinate system.
Explain (in detail) two methods that will make the right line the
same height as the left, without setting the 0.5 dimension to
zero. Correct Answers 1. Constrain one point from each line to
be Horizontal, replacing the 0.50 dimension.
2. Create a second 2.00 dimension for the line on the right,
replacing the 0.50 dimension.
3. Draw a vertical centerline between the two lines and constrain
one point on each side to be symmetrical.
4. Constraint the two lines to be Coincident.
Explain how to delete a constraint. What will automatically
happen when you delete the constraint? Correct Answers Select
the constraint by left-clicking it. Then press the Delete key on
your keyboard. Creo will automatically put in a weak dimension
so that the sketch is still fully dimensioned.
Explain how to select a repeat region. Be specific. Correct
Answers Under Table select the Repeat Region button. Click
Add in the menu. Left click a cell in one corner of the desired
Solutions
Bidirectional Associative Property Correct Answers Ability to
ensure that if any modifications are made in a particular model
in one mode, the corresponding modifications are also reflected
in the same model in other modes.
Constraint Correct Answers Defines position and size of one
entity to another: parallel, same size, perpendicular, tangent.
Copy Correct Answers Paste with options >
✅Dependant Copy
• Fully dependant with options to vary
✅ Advanced reference configuration
Could you put the BOM table in the format instead of the
drawing file? If you could do this, what would be the benefits?
Correct Answers Yes you can put the BOM in the format. This
would allow you to position the table by picking a corner. It also
means that you don't need to set up the table for each drawing,
saving time.
Creo Parametric 3.0 Correct Answers 1. Allows you to
manipulate any solid model dynamically.
2. Calculates the mass properties directly from the created
geometry.
3. Enables the real-time rendering of solid models.
Design Intent Correct Answers Create the model using
dimensions and constraints that are used for fabrication and
, inspection. Also, build it so that changing a dimension value will
cause the model to grow or shrink accordingly, rather than turn
into a shape that was not intended. (Example: a symmetric
model should remain symmetric if a dimension value is
changed).
Dimension Correct Answers Measurement of one or more
entities.
Entity Correct Answers An element of geometry in a cross-
section: line, point, circle, conic, or coordinate system.
Explain (in detail) two methods that will make the right line the
same height as the left, without setting the 0.5 dimension to
zero. Correct Answers 1. Constrain one point from each line to
be Horizontal, replacing the 0.50 dimension.
2. Create a second 2.00 dimension for the line on the right,
replacing the 0.50 dimension.
3. Draw a vertical centerline between the two lines and constrain
one point on each side to be symmetrical.
4. Constraint the two lines to be Coincident.
Explain how to delete a constraint. What will automatically
happen when you delete the constraint? Correct Answers Select
the constraint by left-clicking it. Then press the Delete key on
your keyboard. Creo will automatically put in a weak dimension
so that the sketch is still fully dimensioned.
Explain how to select a repeat region. Be specific. Correct
Answers Under Table select the Repeat Region button. Click
Add in the menu. Left click a cell in one corner of the desired