Mechanical Engineering Midterm
Study Guide Latest Update 2025/2026
GRADED A+
Individuals who are responsible for implementing the corrective action - correct
answerAudits of environmental or quality systems within an organization typically do not
include
More likely - correct answerThe risk of injury for new employees is __________ than for
those with experience
Have the recipient rephrase what was said in his/her own words - correct answerTo
make sure the receiver has understood a message, you should
Threshold limit value (TLV) - correct answerWhat term is used to express the airborne
concentration of materials to which most persons can be exposed to day after day
without adverse effects?
Within 8 hours - correct answerOSHA requires reporting of incidents that hospitalize at
least three workers or kill one or more workers
B - correct answerGas fires are considered type ______________ fires
Internal customer - correct answerThe person who performs the next step in a
production process is a/an _______________ to the person performing the previous
step
Annually - correct answerThe 8-hour hazmat refresher training is required every
Safety glasses and a face shield - correct answerWhen using a grinder, the operator
should wear
Department of Transportation - correct answerTransportation of hazardous materials is
regulated by
42 - correct answerA guardrail must be _______ inches high
File card - correct answerA ______ is used to properly clean a file
Document an itemized sequence of job tasks - correct answerThe first step to a job
safety analysis is to:
, Reject the load to the carrier - correct answerAn employee questions the quality of the
materials inside a trailer and pages his/her supervisor to come to the trailer. It is clear
that the contents have been seriously damaged in shipment. Which of the following
actions is appropriate?
The distance between rungs shall exceed 16" - correct answerWhich of the following is
NOT requirement of a fixed ladder?
An OSHA representative - correct answerA job safety analysis should NOT be
conducted by
Black on yellow - correct answerWhich color combination is commonly used on a
Hazardous Material Identification System (HMIS) chart to indicate stability.
High frequency sounds - correct answerNoise-induced hearing loss first affects the
ability to hear
Responding to worker safety concerns - correct answerMembers of a safety committee
generally include both frontline workers and managers. One of the primary duties of the
safety committee is
Presence of a visible sheen of oil on the water - correct answerWhat should be checked
before draining a diked area of rainwater?
Third party safety consultants - correct answerWhich of the following external parties
would be used to insure compliance with safety guards?
Eliminate the hazard by changing the process - correct answerWhen a hazardous
situation is discovered during an inspection, action must be taken. The best solution is
to
Brainstorm ideas - correct answerA good way to initiate development of an action plan
is to
Providing proper grounding of the tool - correct answerThe plug of a safely designed
110vt power tool has a third wire for
35 feet - correct answerWhat distance should the floor be kept free of combustible
materials when welding or cutting?
Zero - correct answerHow many air hoses can safely cross a walkway?
The material being shipped - correct answerThe United Nations (UN) prefix for a
hazardous material is used to identify
Study Guide Latest Update 2025/2026
GRADED A+
Individuals who are responsible for implementing the corrective action - correct
answerAudits of environmental or quality systems within an organization typically do not
include
More likely - correct answerThe risk of injury for new employees is __________ than for
those with experience
Have the recipient rephrase what was said in his/her own words - correct answerTo
make sure the receiver has understood a message, you should
Threshold limit value (TLV) - correct answerWhat term is used to express the airborne
concentration of materials to which most persons can be exposed to day after day
without adverse effects?
Within 8 hours - correct answerOSHA requires reporting of incidents that hospitalize at
least three workers or kill one or more workers
B - correct answerGas fires are considered type ______________ fires
Internal customer - correct answerThe person who performs the next step in a
production process is a/an _______________ to the person performing the previous
step
Annually - correct answerThe 8-hour hazmat refresher training is required every
Safety glasses and a face shield - correct answerWhen using a grinder, the operator
should wear
Department of Transportation - correct answerTransportation of hazardous materials is
regulated by
42 - correct answerA guardrail must be _______ inches high
File card - correct answerA ______ is used to properly clean a file
Document an itemized sequence of job tasks - correct answerThe first step to a job
safety analysis is to:
, Reject the load to the carrier - correct answerAn employee questions the quality of the
materials inside a trailer and pages his/her supervisor to come to the trailer. It is clear
that the contents have been seriously damaged in shipment. Which of the following
actions is appropriate?
The distance between rungs shall exceed 16" - correct answerWhich of the following is
NOT requirement of a fixed ladder?
An OSHA representative - correct answerA job safety analysis should NOT be
conducted by
Black on yellow - correct answerWhich color combination is commonly used on a
Hazardous Material Identification System (HMIS) chart to indicate stability.
High frequency sounds - correct answerNoise-induced hearing loss first affects the
ability to hear
Responding to worker safety concerns - correct answerMembers of a safety committee
generally include both frontline workers and managers. One of the primary duties of the
safety committee is
Presence of a visible sheen of oil on the water - correct answerWhat should be checked
before draining a diked area of rainwater?
Third party safety consultants - correct answerWhich of the following external parties
would be used to insure compliance with safety guards?
Eliminate the hazard by changing the process - correct answerWhen a hazardous
situation is discovered during an inspection, action must be taken. The best solution is
to
Brainstorm ideas - correct answerA good way to initiate development of an action plan
is to
Providing proper grounding of the tool - correct answerThe plug of a safely designed
110vt power tool has a third wire for
35 feet - correct answerWhat distance should the floor be kept free of combustible
materials when welding or cutting?
Zero - correct answerHow many air hoses can safely cross a walkway?
The material being shipped - correct answerThe United Nations (UN) prefix for a
hazardous material is used to identify
