1 | Page
NEIEP 200 Final Review Questions and
Correct Answers
Which lay of wire rope has the strand wires in line with the rope
axis? Ans: — Regular Lay
At what speed should the counterweight safeties be set to trip?
Ans: — Up to 10% higher than the car governor
Which type of safety uses an oil buffer between the car and safety
planks? Ans: — Type C
What is the purpose of the terminal motion switch? Ans: — slow
down and stop the car automatically at or near the top or bottom
landing
If you have a 3500 lb. car rated at 4000 lbs. capacity, how much
should the counterweight assembly weigh for a normal 40%
installation? Ans: — 5100 lbs.
When the pit directional limit switch is actuated, the normal
circuits will allow the car to run Ans: — Up
_______should not be disassembled in the field. Ans: — Oil Buffers
The loss of traction between the hoist ropes and the machine
driver when the counterweight lands on its buffer avoids... Ans: —
The elevator car being pulled into the over head.
Refer to Table 1. With a safety factor of 5, what is the breaking
strength for 1 1/8" nylon rope? Ans: — 52,000 lbs.
Which of the following applies to rope usage? Ans: — Prevent
manila rope from unraveling by using whipping.
© 2025 All rights reserved
, 2 | Page
What does the designation 3/8" 6 X 30 improved plow steel mean?
Ans: — It is a high strength cable with 6 strands composed of 30
wires per strand?
When using Crosby clips, which of the following statements is
correct? Ans: — To determine the correct minimum spacing
multiply the rope diameter times 6.
When handling and storing a freight platform, what do you need to
keep in mind? Ans: — With the platform on edge, handle it from
the ends and move on rollers.
Which of the following statements is true concerning capstans?
Ans: — Both b, and c.
b. Fasten the hoist to a beam or other building structure.
c. To interrupt hoisting ease off on the pulling rope
When choosing planks for hoisting, what must be considered?
Ans: — Use only scaffold grade lumber
The distance between the counterweight buffer strike plate and
the striking surface of the counterweight buffer when the car floor
is level with the top terminal landing is known as Ans: — Runby
What type of wrench is used to align the holes for rail installation?
Ans: — Spud Wrench
Which of the following wrenches is used to thread pipes with
polished surfaces together? Ans: — Strap Wrench
Which of the following statements applies to the use of a hacksaw
on the job? Ans: — Hacksaw blades must be installed with the
teeth facing forward.
The operation of the down final limit switch will prevent
movement of the car by normal operating devices in ... Ans: —
both directions of travel
© 2025 All rights reserved
NEIEP 200 Final Review Questions and
Correct Answers
Which lay of wire rope has the strand wires in line with the rope
axis? Ans: — Regular Lay
At what speed should the counterweight safeties be set to trip?
Ans: — Up to 10% higher than the car governor
Which type of safety uses an oil buffer between the car and safety
planks? Ans: — Type C
What is the purpose of the terminal motion switch? Ans: — slow
down and stop the car automatically at or near the top or bottom
landing
If you have a 3500 lb. car rated at 4000 lbs. capacity, how much
should the counterweight assembly weigh for a normal 40%
installation? Ans: — 5100 lbs.
When the pit directional limit switch is actuated, the normal
circuits will allow the car to run Ans: — Up
_______should not be disassembled in the field. Ans: — Oil Buffers
The loss of traction between the hoist ropes and the machine
driver when the counterweight lands on its buffer avoids... Ans: —
The elevator car being pulled into the over head.
Refer to Table 1. With a safety factor of 5, what is the breaking
strength for 1 1/8" nylon rope? Ans: — 52,000 lbs.
Which of the following applies to rope usage? Ans: — Prevent
manila rope from unraveling by using whipping.
© 2025 All rights reserved
, 2 | Page
What does the designation 3/8" 6 X 30 improved plow steel mean?
Ans: — It is a high strength cable with 6 strands composed of 30
wires per strand?
When using Crosby clips, which of the following statements is
correct? Ans: — To determine the correct minimum spacing
multiply the rope diameter times 6.
When handling and storing a freight platform, what do you need to
keep in mind? Ans: — With the platform on edge, handle it from
the ends and move on rollers.
Which of the following statements is true concerning capstans?
Ans: — Both b, and c.
b. Fasten the hoist to a beam or other building structure.
c. To interrupt hoisting ease off on the pulling rope
When choosing planks for hoisting, what must be considered?
Ans: — Use only scaffold grade lumber
The distance between the counterweight buffer strike plate and
the striking surface of the counterweight buffer when the car floor
is level with the top terminal landing is known as Ans: — Runby
What type of wrench is used to align the holes for rail installation?
Ans: — Spud Wrench
Which of the following wrenches is used to thread pipes with
polished surfaces together? Ans: — Strap Wrench
Which of the following statements applies to the use of a hacksaw
on the job? Ans: — Hacksaw blades must be installed with the
teeth facing forward.
The operation of the down final limit switch will prevent
movement of the car by normal operating devices in ... Ans: —
both directions of travel
© 2025 All rights reserved
