Sophos S80 Technician Exam QUESTIONS AND CORRECT
ANSWERS 2025/2026 (VERIFIED ANSWERS) ALREADY GRADED
A+ / NEWEST EXAM!!!
Where would you perform an Ethernet card test? - ANSWERS-Sf loader
Both devices in an active-passive high availability pair become the primary
device. What is the most likely cause? - ANSWERS-
What CONSOLE command can you use to check there is space on the
report partition? - ANSWERS-
What partition is reporting data stored on? - ANSWERS-var
Which 3 services should you check when troubleshooting issues with
reports? - ANSWERS-
What is the maximum number of external syslog servers you can configure
on Sophos Firewall? - ANSWERS-5
You are accessing log files using the Advanced Shell. Which folder are
they located in? - ANSWERS-/log
Arrange the routes in order of precedence, with the highest precedence at
the top? - ANSWERS-Health check, Static, SD-WAN, VPN, Default
, What command would you run on the console to see which type of routes
are being processed first? - ANSWERS-system route_precedence show
What command would you run on the advanced shell to see the route
table? - ANSWERS-ip rule show
What can you enter when prompted for the password in the Device
Console to revert the default admin password? - ANSWERS-RESET
What command do you enter in Device Console to find out why Sophos
Firewall is in failsafe mode? - ANSWERS-show failure-reason
In the log viewer you can see what type of firewall rule is being matched;
network, user, or web server. What type of rule would be matched if the
policy type was 2? - ANSWERS-User Firewall Rule
When creating a firewall rule to allow traffic that matches a DNAT rule,
what destination IP should be used? - ANSWERS-PRE-NAT
If you see the following on the console, what does it most likely mean?
console > system firewall-acceleration show
Firewall Acceleration is Enabled. Fastpath load failed - ANSWERS-There is
no supported network driver
You want to check the configuration of enable_appsignatures for IPS. What
command do you run on the console? - ANSWERS-ips-settings
ANSWERS 2025/2026 (VERIFIED ANSWERS) ALREADY GRADED
A+ / NEWEST EXAM!!!
Where would you perform an Ethernet card test? - ANSWERS-Sf loader
Both devices in an active-passive high availability pair become the primary
device. What is the most likely cause? - ANSWERS-
What CONSOLE command can you use to check there is space on the
report partition? - ANSWERS-
What partition is reporting data stored on? - ANSWERS-var
Which 3 services should you check when troubleshooting issues with
reports? - ANSWERS-
What is the maximum number of external syslog servers you can configure
on Sophos Firewall? - ANSWERS-5
You are accessing log files using the Advanced Shell. Which folder are
they located in? - ANSWERS-/log
Arrange the routes in order of precedence, with the highest precedence at
the top? - ANSWERS-Health check, Static, SD-WAN, VPN, Default
, What command would you run on the console to see which type of routes
are being processed first? - ANSWERS-system route_precedence show
What command would you run on the advanced shell to see the route
table? - ANSWERS-ip rule show
What can you enter when prompted for the password in the Device
Console to revert the default admin password? - ANSWERS-RESET
What command do you enter in Device Console to find out why Sophos
Firewall is in failsafe mode? - ANSWERS-show failure-reason
In the log viewer you can see what type of firewall rule is being matched;
network, user, or web server. What type of rule would be matched if the
policy type was 2? - ANSWERS-User Firewall Rule
When creating a firewall rule to allow traffic that matches a DNAT rule,
what destination IP should be used? - ANSWERS-PRE-NAT
If you see the following on the console, what does it most likely mean?
console > system firewall-acceleration show
Firewall Acceleration is Enabled. Fastpath load failed - ANSWERS-There is
no supported network driver
You want to check the configuration of enable_appsignatures for IPS. What
command do you run on the console? - ANSWERS-ips-settings
