J-STD-001 2025 QUESTION WITH 100%
ACCURATE ANSWERS (GUARANTEED A PASS)
Who is responsible for identifying the assembly class? - ANS-User
What is a defect? - ANS-A condition that may affect the form, fit, or function of the item in the
end use environment
Hardware found to not conform to the requirements of the standard shall be classified as defects
and dispositioned for: - ANS-[D1D2D3]
There shall be no broken strands for wires used at a potential of 6kV or greater: - ANS-
[D1D2D3]
A documented process control system shall be implemented for: - ANS-[N1N2D3]
The contract shall take precedence over this standard for: - ANS-[D1D2D3]
What is wire overlap? - ANS-When a wire is wrapped more than 360 and crosses over itself
What is wire over wrap? - ANS-When a wire is wrapped more than 360 and remains in contact
with the terminal
Manufacturers shall perform 100% inspection unless sampling inspection is defined for: - ANS-
[N1D2D3]
Inspection of soldering and cleanliness shall be performed prior to conformal coasting, staking,
or encapsulation for: - ANS-[N1D2D3]
, Illumination at the surface of work stations should be at least what? - ANS-1000 lux
What is the tolerance for magnification aids? - ANS-+- 15%
Eating, drinking, smoking, e-cigs use shall be prohibited at the work station for: - ANS-
[D1D2D3]
Manufacturer shall verify ESD is adequate when humidity falls below 30% for: - ANS-
[N1D2D3]
Manufacturer shall establish an ESD control program for: - ANS-[D1D2D3]
What is J-STD-002? - ANS-Solder-ability tests for Component leads, terminations, lugs, wires,
and terminals
What is J-STD-003? - ANS-Solder ability tests for printed boards
What is J-STD-004? - ANS-Requirements for Soldering Fluxes
What is J-STD-005? - ANS-Requirements for Soldering Paste
What is J-STD-006? - ANS-Requirements for electronic grade solder alloys, fluxed and non-
fluxed solid solders
Manufacturers shall have a Pb-free control plan for: - ANS-[N1N2D3]
Items exposed to uncured silicone material shall not be used for processing other material for: -
ANS-[D1D2D3]
ACCURATE ANSWERS (GUARANTEED A PASS)
Who is responsible for identifying the assembly class? - ANS-User
What is a defect? - ANS-A condition that may affect the form, fit, or function of the item in the
end use environment
Hardware found to not conform to the requirements of the standard shall be classified as defects
and dispositioned for: - ANS-[D1D2D3]
There shall be no broken strands for wires used at a potential of 6kV or greater: - ANS-
[D1D2D3]
A documented process control system shall be implemented for: - ANS-[N1N2D3]
The contract shall take precedence over this standard for: - ANS-[D1D2D3]
What is wire overlap? - ANS-When a wire is wrapped more than 360 and crosses over itself
What is wire over wrap? - ANS-When a wire is wrapped more than 360 and remains in contact
with the terminal
Manufacturers shall perform 100% inspection unless sampling inspection is defined for: - ANS-
[N1D2D3]
Inspection of soldering and cleanliness shall be performed prior to conformal coasting, staking,
or encapsulation for: - ANS-[N1D2D3]
, Illumination at the surface of work stations should be at least what? - ANS-1000 lux
What is the tolerance for magnification aids? - ANS-+- 15%
Eating, drinking, smoking, e-cigs use shall be prohibited at the work station for: - ANS-
[D1D2D3]
Manufacturer shall verify ESD is adequate when humidity falls below 30% for: - ANS-
[N1D2D3]
Manufacturer shall establish an ESD control program for: - ANS-[D1D2D3]
What is J-STD-002? - ANS-Solder-ability tests for Component leads, terminations, lugs, wires,
and terminals
What is J-STD-003? - ANS-Solder ability tests for printed boards
What is J-STD-004? - ANS-Requirements for Soldering Fluxes
What is J-STD-005? - ANS-Requirements for Soldering Paste
What is J-STD-006? - ANS-Requirements for electronic grade solder alloys, fluxed and non-
fluxed solid solders
Manufacturers shall have a Pb-free control plan for: - ANS-[N1N2D3]
Items exposed to uncured silicone material shall not be used for processing other material for: -
ANS-[D1D2D3]
