TEXAS WASTEWATER CLASS C
EXAM TEST BANK | ALL QUESTIONS
AND CORRECT ANSWERS | ALREADY
GRADED A+ | VERIFIED ANSWERS |
LATEST VERSION
The Activated Sludge Process:
A. requires preaeration
B. requires Activated Carbon
C. is an aerobic biological process.
D. Usually precedes primary sedimentation.
E. Requires 50% by volume old sludge to work effectively. - CORRECT ANSWER-C. Is
an Aerobic biological process
A complete mix activated sludge plant has a fast settling sludge and high amounts of
pin floc leaving the clarifier. One way to correct this problem is to :
A. Increase the RAS Flow
B. Reduce Wasting Rates
C. Increase dissolved oxygen levels.
D. Increase the F/M ratio by wasting more
E. Increase the sludge age by wasting less. - CORRECT ANSWER-D. Increase the F/M
Ratio by Wasting More
, Which of the following flow rates should be measured if the operator is to control plant
properly?
A. Aeration rate or resulting dissolved oxygen level.
B. Influent or effluent.
C. return sludge
D. waste sludge
E. all the above - CORRECT ANSWER-E. all the above
During start up your aeration tank produces excessive amounts of billowing white foam.
This can be corrected by:
A. Doing nothing, it will go away in a few hours
B. Increasing the sludge wasting rate
C. Seeding the process with sufficient good quality sludge
D. Spraying water on the foam until it is gone
E. Taking a weeks vacation - CORRECT ANSWER-C. Seeding the process with
sufficient good quality sludge
In solving an operational problem at a treatment plant:
A. there is almost always a good technical solution. It may require considerable
experience and time to learn whaat it is.
B. Human errors have to be corrected since the operator is at fault.
C. don't let the laboratory personnel influence you're judgement as to what the best
solution is.
D. standard textbooks in sanitary engineering are the best source of information.
EXAM TEST BANK | ALL QUESTIONS
AND CORRECT ANSWERS | ALREADY
GRADED A+ | VERIFIED ANSWERS |
LATEST VERSION
The Activated Sludge Process:
A. requires preaeration
B. requires Activated Carbon
C. is an aerobic biological process.
D. Usually precedes primary sedimentation.
E. Requires 50% by volume old sludge to work effectively. - CORRECT ANSWER-C. Is
an Aerobic biological process
A complete mix activated sludge plant has a fast settling sludge and high amounts of
pin floc leaving the clarifier. One way to correct this problem is to :
A. Increase the RAS Flow
B. Reduce Wasting Rates
C. Increase dissolved oxygen levels.
D. Increase the F/M ratio by wasting more
E. Increase the sludge age by wasting less. - CORRECT ANSWER-D. Increase the F/M
Ratio by Wasting More
, Which of the following flow rates should be measured if the operator is to control plant
properly?
A. Aeration rate or resulting dissolved oxygen level.
B. Influent or effluent.
C. return sludge
D. waste sludge
E. all the above - CORRECT ANSWER-E. all the above
During start up your aeration tank produces excessive amounts of billowing white foam.
This can be corrected by:
A. Doing nothing, it will go away in a few hours
B. Increasing the sludge wasting rate
C. Seeding the process with sufficient good quality sludge
D. Spraying water on the foam until it is gone
E. Taking a weeks vacation - CORRECT ANSWER-C. Seeding the process with
sufficient good quality sludge
In solving an operational problem at a treatment plant:
A. there is almost always a good technical solution. It may require considerable
experience and time to learn whaat it is.
B. Human errors have to be corrected since the operator is at fault.
C. don't let the laboratory personnel influence you're judgement as to what the best
solution is.
D. standard textbooks in sanitary engineering are the best source of information.
