Auto Tech Final REAL ONE
Study online at https://quizlet.com/_hr73w3
1. 1. Which part is most likely the problem if a light does not come on during an
instrument panel bulb check?: A. bulb
2. 2. Which color is the primary brake warning light on the dash of cars and
trucks?: C. red
3. 3. Carquest, NAPA, and Jiffy Lube are examples of:: B. franchises.
4. 4. What organization certifies automotive technicians?: A. ASE
5. 5. NATEF certifies automotive:: D. training programs.
6. 6. When one is working on an HID lighting system, which should be discon-
nected?: B. battery
7. 7. What should a student do when a broken tool is found in the shop?: C. inform
the instructor
8. 8. Technician A says mopping up a spill is a good safety practice to use in
the shop. Technician B says leaving one's workstation a mess is a good safety
practice to use in the shop. Who is right?: A. A only
9. 9. Where is a fire evacuation route located?: A. beside classroom door
10. 10. What color is the wiring loom going through the steering column for the
supplemental restraint system?: D. yellow
11. 11. What color are the painted lines on the floor that define a work area?: D.
yellow
12. 12. Using the OSHA system of safety colors, what color strip would indicate
the location of the shop eyewash station?: B. green and white
13. 13. Technician A says wearing a long necklace in the shop is a good safety
practice. Technician B says long hair is acceptable while working around mov-
ing engine parts. Who is right?: D. Neither A nor B
14. 14. Which activity requires the use of nitrile gloves?: C. using a parts washer
15. 15. Jack stands should be placed under lifted vehicles to prevent the vehicles
from:: A. falling.
16. 16. What do the yellow lines on an automotive shop floor indicate?: A. caution
17. 17. Who is allowed to read safety data sheets?: A. everyone
18. 18. Before servicing the supplemental restraint system, what should a tech-
nician do as a safety precaution?: B. disarm the system
1/7
, Auto Tech Final REAL ONE
Study online at https://quizlet.com/_hr73w3
19. 19. When a bolt or nut is too tight to loosen with the socket currently being
used, which is the safest solution?: A. Use a larger drive size.
20. 20. An SRS warning light is displayed on the vehicle instrument cluster. What
does this light represent?: A. bad airbag
21. 21. When using a fire extinguisher, what do the letters PASS stand for?: C. pull
aim squeeze sweep
22. 22. What is the risk of wearing a ring on one's hand while working on a
vehicle?: B. It causes an electrical burn.
23. 23. Which part of a vehicle is an acceptable lifting point?: C. pinch weld
24. 24. An electrical fire is what class of fire?: C. Class C
25. 25. What could be the result of running a vehicle in the shop without proper
ventilation?: A. death
26. 26. Which is the correct lubricant for the front axle on a rear-wheel-drive
car?: D. wheel bearing grease
27. 27. Technician A says it is acceptable to use brake cleaner to clean throttle
bodies. Technician B says it is acceptable to mix DOT 5 brake fluid with DOT 3
brake fluid. Who is right?: D. Neither A nor B
28. 28. Where should cleaning chemicals be stored in the auto shop?: B. fire-retardant
cabinet
29. 29. Which type of socket will best hold a nut and/or bolt?: B. 6 point
30. 30. Which tool should be used to remove an oil filter?: D. oil filter wrench
31. 31. To prevent damage to the vehicle's paint, what safety precaution should
a technician take before working on an engine?: B. install fender covers
32. 32. Why would a technician not use the open end of a wrench to untighten
a frozen nut or bolt on a vehicle?: B. rounds the fastener
33. 33. Which tool is used to remove snap rings?: B. snap ring pliers
34. 34. Which tool would most likely be used to remove a brake line?: D. tubing wrench
35. 35. Where should micrometers be stored while not being used?: A. in a wooden or
plastic box
36. 36. What tool would be used to measure the thickness of a solid metal rod?: D.
outside micrometer
2/7
Study online at https://quizlet.com/_hr73w3
1. 1. Which part is most likely the problem if a light does not come on during an
instrument panel bulb check?: A. bulb
2. 2. Which color is the primary brake warning light on the dash of cars and
trucks?: C. red
3. 3. Carquest, NAPA, and Jiffy Lube are examples of:: B. franchises.
4. 4. What organization certifies automotive technicians?: A. ASE
5. 5. NATEF certifies automotive:: D. training programs.
6. 6. When one is working on an HID lighting system, which should be discon-
nected?: B. battery
7. 7. What should a student do when a broken tool is found in the shop?: C. inform
the instructor
8. 8. Technician A says mopping up a spill is a good safety practice to use in
the shop. Technician B says leaving one's workstation a mess is a good safety
practice to use in the shop. Who is right?: A. A only
9. 9. Where is a fire evacuation route located?: A. beside classroom door
10. 10. What color is the wiring loom going through the steering column for the
supplemental restraint system?: D. yellow
11. 11. What color are the painted lines on the floor that define a work area?: D.
yellow
12. 12. Using the OSHA system of safety colors, what color strip would indicate
the location of the shop eyewash station?: B. green and white
13. 13. Technician A says wearing a long necklace in the shop is a good safety
practice. Technician B says long hair is acceptable while working around mov-
ing engine parts. Who is right?: D. Neither A nor B
14. 14. Which activity requires the use of nitrile gloves?: C. using a parts washer
15. 15. Jack stands should be placed under lifted vehicles to prevent the vehicles
from:: A. falling.
16. 16. What do the yellow lines on an automotive shop floor indicate?: A. caution
17. 17. Who is allowed to read safety data sheets?: A. everyone
18. 18. Before servicing the supplemental restraint system, what should a tech-
nician do as a safety precaution?: B. disarm the system
1/7
, Auto Tech Final REAL ONE
Study online at https://quizlet.com/_hr73w3
19. 19. When a bolt or nut is too tight to loosen with the socket currently being
used, which is the safest solution?: A. Use a larger drive size.
20. 20. An SRS warning light is displayed on the vehicle instrument cluster. What
does this light represent?: A. bad airbag
21. 21. When using a fire extinguisher, what do the letters PASS stand for?: C. pull
aim squeeze sweep
22. 22. What is the risk of wearing a ring on one's hand while working on a
vehicle?: B. It causes an electrical burn.
23. 23. Which part of a vehicle is an acceptable lifting point?: C. pinch weld
24. 24. An electrical fire is what class of fire?: C. Class C
25. 25. What could be the result of running a vehicle in the shop without proper
ventilation?: A. death
26. 26. Which is the correct lubricant for the front axle on a rear-wheel-drive
car?: D. wheel bearing grease
27. 27. Technician A says it is acceptable to use brake cleaner to clean throttle
bodies. Technician B says it is acceptable to mix DOT 5 brake fluid with DOT 3
brake fluid. Who is right?: D. Neither A nor B
28. 28. Where should cleaning chemicals be stored in the auto shop?: B. fire-retardant
cabinet
29. 29. Which type of socket will best hold a nut and/or bolt?: B. 6 point
30. 30. Which tool should be used to remove an oil filter?: D. oil filter wrench
31. 31. To prevent damage to the vehicle's paint, what safety precaution should
a technician take before working on an engine?: B. install fender covers
32. 32. Why would a technician not use the open end of a wrench to untighten
a frozen nut or bolt on a vehicle?: B. rounds the fastener
33. 33. Which tool is used to remove snap rings?: B. snap ring pliers
34. 34. Which tool would most likely be used to remove a brake line?: D. tubing wrench
35. 35. Where should micrometers be stored while not being used?: A. in a wooden or
plastic box
36. 36. What tool would be used to measure the thickness of a solid metal rod?: D.
outside micrometer
2/7
