ASQ CQT Exam
One advantage of 100% inspection over sampling
inspection is that 100% inspection
(A) provides more information about quality levels
(B) gives zero defects to the customer
(C) reduces the personal bias of the inspector
(D) requires less machine-operator training - answer A provides more information about
quality levels
When the term "R & R" is applied to digital calipers, it
refers to
(A) removal and replacement
(B) relativity and reproducibility
(C) repeatability and reliability
(D) repeatability and reproducibility - answerD repeatability and reproducibility
The proper method of placing parts on a surface plate and then removing them is
(A) rotate on and slide off
(B) rotate on and lift off
(C) set on and slide off
(D) set on and lift off - answerA rotate on and slide off
Who is responsible for determining whether a follow-up response is sufficient to close
out an internal audit?
(A) Executive management
(B) The quality manager
(C) The audit team leader
(D) The internal auditee - answerC The audit team leader
Which of the following methods is used to develop an exhaustive list of ideas about a
subject?
(A) Goal-setting
(B) Brainstorming
(C) Benchmarking
(D) Problem-solving - answerB Brainstorming
A document that asserts that a product conforms to
specification is known as a certificate of
(A) qualification
(B) validation
(C) calibration
(D) compliance - answerD compliance
, Confidence limits are generated in order to define the
(A) limits of random variation around a control value
(B) limits that contain all future observations
(C) interval within which a population parameter lies
(D) amount of variation that the process exhibits - answerC interval within which a
population parameter lies
The purpose of a calibration schedule is to
(A) detect deterioration of accuracy
(B) meet ISO audit requirements
(C) test inspector performance
(D) increase product acceptance - answerA detect deterioration of accuracy
What is the percent yield for a normally distributed
process in which the item length specification is
5.750 ± 0.004, X is 5.752, and the standard deviation is
0.002 ?
(A) 15.73%
(B) 19.15%
(C) 47.72%
(D) 83.99% - answerD 83.99%
In preparation for construction of a cause and effect
diagram, it is important to
(A) plot separate charts for each source
(B) focus only on what makes things go wrong
(C) record everything people suggest
(D) validate possible root causes - answerC record everything people suggest
A quality technician uses a c chart to monitor the number of defects in a square foot of
material. After the initial startup period, the mean number of defects is calculated at
13.5. What should the control limits be for the c chart?
LCL UCL
(A) 0.00 54.00
(B) 0.00 27.00
(C) 2.48 24.52
(D) 9.83 17.17 - answerC 2.48 24.52
-
--
--
--
--
- ----------
The shape of the distribution above is best described as
One advantage of 100% inspection over sampling
inspection is that 100% inspection
(A) provides more information about quality levels
(B) gives zero defects to the customer
(C) reduces the personal bias of the inspector
(D) requires less machine-operator training - answer A provides more information about
quality levels
When the term "R & R" is applied to digital calipers, it
refers to
(A) removal and replacement
(B) relativity and reproducibility
(C) repeatability and reliability
(D) repeatability and reproducibility - answerD repeatability and reproducibility
The proper method of placing parts on a surface plate and then removing them is
(A) rotate on and slide off
(B) rotate on and lift off
(C) set on and slide off
(D) set on and lift off - answerA rotate on and slide off
Who is responsible for determining whether a follow-up response is sufficient to close
out an internal audit?
(A) Executive management
(B) The quality manager
(C) The audit team leader
(D) The internal auditee - answerC The audit team leader
Which of the following methods is used to develop an exhaustive list of ideas about a
subject?
(A) Goal-setting
(B) Brainstorming
(C) Benchmarking
(D) Problem-solving - answerB Brainstorming
A document that asserts that a product conforms to
specification is known as a certificate of
(A) qualification
(B) validation
(C) calibration
(D) compliance - answerD compliance
, Confidence limits are generated in order to define the
(A) limits of random variation around a control value
(B) limits that contain all future observations
(C) interval within which a population parameter lies
(D) amount of variation that the process exhibits - answerC interval within which a
population parameter lies
The purpose of a calibration schedule is to
(A) detect deterioration of accuracy
(B) meet ISO audit requirements
(C) test inspector performance
(D) increase product acceptance - answerA detect deterioration of accuracy
What is the percent yield for a normally distributed
process in which the item length specification is
5.750 ± 0.004, X is 5.752, and the standard deviation is
0.002 ?
(A) 15.73%
(B) 19.15%
(C) 47.72%
(D) 83.99% - answerD 83.99%
In preparation for construction of a cause and effect
diagram, it is important to
(A) plot separate charts for each source
(B) focus only on what makes things go wrong
(C) record everything people suggest
(D) validate possible root causes - answerC record everything people suggest
A quality technician uses a c chart to monitor the number of defects in a square foot of
material. After the initial startup period, the mean number of defects is calculated at
13.5. What should the control limits be for the c chart?
LCL UCL
(A) 0.00 54.00
(B) 0.00 27.00
(C) 2.48 24.52
(D) 9.83 17.17 - answerC 2.48 24.52
-
--
--
--
--
- ----------
The shape of the distribution above is best described as
