CSX Conductor FINAL REVIEW UPDATED ACTUAL Questions and CORRECT
Answers
not necessarily parallel, consisting of two switches whose
Who is Responsible for making Pay Claims?
What is the Hand Signal for Reduce Speed?
Which of the following are allowed by the Rulebook?
What is the Hand Signal for Release Air Brakes?
Who authorizes a Utility Employee to join an Assigned
Crew?
What is the normal position for a switch or derail?
Before lining a switch or derail, an employee must?
If a lock is found to be defective or missing on a main line
switch or derail an employee must?
When an Employee determines that a switch or derail is
defective, the employee must?
You are standing in a yard using multiple switches on long
shoves. After lining each switch an employee should check
what?
When using a portable radio in a shove move, Employee
instructions must specify what?
What is a System of Tracks, other than main tracks and
sidings, used for making up trains for storing cars and
other purposes?
By Definition, what is the location in a turnout where it is
unsafe to pass on an adjacent track?
What is a track connection between two adjacent tracks,
, Crossover
Ranking Employee or Employee to be
paidArm out horizontal over the track
Always take the safe course
Hand held overhead when Equipment is Standing
Ranking Employee
In the "on" or derailing position
1) Ensure that any preceeding movement has passed
clearance points. 2) Ensure that the device is not
locked,spiked, or tagged "out of service"
1) Report device to Trainmaster/Dispatcher. 2) Be gov-
erned by the instructions of said
Dispatcher/Trainmaster
1) Not operate the device. 2) Report device to
ProperAuthority
That all switch points are flush and aligned
properly.
1) Employee is clear of all tracks. 2) Switches and
Derailsare all properly aligned for the move
Yard
Clearance Point
, primary purpose is to allow crossing from one track to
another?
What is a device of "Necessary Track" used to change from
Switch
one track to another?
What is the the minimum distance you must stand from a
30'
switch or derail involved in the route of a passing train?
When crossing tracks with standing equipment, what 1) Stop and check both directions. 2) Do not cross within
safety precautions must be taken? 25' of standing equipment.
In addition to facing the equipment and maintaining 3 1) Avoid getting off equipment in an unsafe area. 2)Stop
points of contact, what other steps must be taken when at the bottom rung and observe where you will be placing
disembarking moving equipment? your foot.
When crossing standing equipment you must find sufl-
putting feet on coupler, air hose, anglecocks etc.
cient handholds and avoid?
when riding a car, maintain 3 points of contact, be pre-
Face direction of movement
pared for unexpected movement, slack actions and?
Do not ride on a car with a grab bar that is less than
12"
above the ground
What is required when riding a car approaching a close
dismount the car prior to reaching the close clearance
clearance?
What can be used to clear foreign materials from a switch? 1) Broom. 2) Switch
1) On duty, or reporting for duty. 2) on CSX Property,
Employees are prohibited from using alcohol...
Vehicles, or facilities provided by CSX
1) Do not extend over the drawbar when adjusting hoses.
When working with air hoses, which of the following ap-
2) make certain that BOTH anglecocks are closed before
ply?
adjusting hoses with hands.
1) Secure EOT air hose by s hook if available. 2) Do not
When handling a EOT device, an employee must...
place the EOT where it may become a tripping hazard
Answers
not necessarily parallel, consisting of two switches whose
Who is Responsible for making Pay Claims?
What is the Hand Signal for Reduce Speed?
Which of the following are allowed by the Rulebook?
What is the Hand Signal for Release Air Brakes?
Who authorizes a Utility Employee to join an Assigned
Crew?
What is the normal position for a switch or derail?
Before lining a switch or derail, an employee must?
If a lock is found to be defective or missing on a main line
switch or derail an employee must?
When an Employee determines that a switch or derail is
defective, the employee must?
You are standing in a yard using multiple switches on long
shoves. After lining each switch an employee should check
what?
When using a portable radio in a shove move, Employee
instructions must specify what?
What is a System of Tracks, other than main tracks and
sidings, used for making up trains for storing cars and
other purposes?
By Definition, what is the location in a turnout where it is
unsafe to pass on an adjacent track?
What is a track connection between two adjacent tracks,
, Crossover
Ranking Employee or Employee to be
paidArm out horizontal over the track
Always take the safe course
Hand held overhead when Equipment is Standing
Ranking Employee
In the "on" or derailing position
1) Ensure that any preceeding movement has passed
clearance points. 2) Ensure that the device is not
locked,spiked, or tagged "out of service"
1) Report device to Trainmaster/Dispatcher. 2) Be gov-
erned by the instructions of said
Dispatcher/Trainmaster
1) Not operate the device. 2) Report device to
ProperAuthority
That all switch points are flush and aligned
properly.
1) Employee is clear of all tracks. 2) Switches and
Derailsare all properly aligned for the move
Yard
Clearance Point
, primary purpose is to allow crossing from one track to
another?
What is a device of "Necessary Track" used to change from
Switch
one track to another?
What is the the minimum distance you must stand from a
30'
switch or derail involved in the route of a passing train?
When crossing tracks with standing equipment, what 1) Stop and check both directions. 2) Do not cross within
safety precautions must be taken? 25' of standing equipment.
In addition to facing the equipment and maintaining 3 1) Avoid getting off equipment in an unsafe area. 2)Stop
points of contact, what other steps must be taken when at the bottom rung and observe where you will be placing
disembarking moving equipment? your foot.
When crossing standing equipment you must find sufl-
putting feet on coupler, air hose, anglecocks etc.
cient handholds and avoid?
when riding a car, maintain 3 points of contact, be pre-
Face direction of movement
pared for unexpected movement, slack actions and?
Do not ride on a car with a grab bar that is less than
12"
above the ground
What is required when riding a car approaching a close
dismount the car prior to reaching the close clearance
clearance?
What can be used to clear foreign materials from a switch? 1) Broom. 2) Switch
1) On duty, or reporting for duty. 2) on CSX Property,
Employees are prohibited from using alcohol...
Vehicles, or facilities provided by CSX
1) Do not extend over the drawbar when adjusting hoses.
When working with air hoses, which of the following ap-
2) make certain that BOTH anglecocks are closed before
ply?
adjusting hoses with hands.
1) Secure EOT air hose by s hook if available. 2) Do not
When handling a EOT device, an employee must...
place the EOT where it may become a tripping hazard
