TATTOO MACHINE COMPREHENSIVE EXAM QUESTIONS
WITH DETAILED VERIFIED AND 100% ACCURATE
ANSWERS BRAND NEW EXAM ALREADY GRADED (A+
PASS)
A -bar Ans✓✓✓Armature bar 1.5 is standard length
When a bar is flat on front coil we are coil has between .010-.012
Ans✓✓✓Smaller creates more power it is noticeable (more coil is more
power)
You should be careful of small gaps as the air bar can hit the coil when
the machine is running Ans✓✓✓And this will cause it to rattle or
Deflection of the a bar. It will Make that a bar bounce off of the rear coil
and hit the front coil in correctly
Armature bar should be Ans✓✓✓Plain steel and no chrome. The coil
cord should not extend over coil cap very much coils with too much
Coors showing tend to run hot. Also they run sporadically after a short
time your machine can run in consistently and will require more voltage
to compensate
Push the a bar down on the front coil hold machine up to the light and
check Ans✓✓✓For dust Lent etc. this can cause your machine to rattle
and deflect believe it or not just blow debris with air can or pouty lips
Do not allow front spring to Ans✓✓✓Hangover the rear of the amateur
Bar this can create a buzz and undue birbration
, Armature bar rear and coil Ans✓✓✓Are aligned
A longer a bar extending past rear is fine Ans✓✓✓Creates a longer
stroke and usually a longer a bar and is 1.625 long
Angle of contact screws does not matter much Ans✓✓✓As long as it
turns on it's doing it's job however when the spring strikes the contact on
the up stroke the angle of the contact screw can have an effect of the
overall vibration of your machine.
Once your machine is set up correctly it should Ans✓✓✓The angle
should remain the same because the Contacts crew should head at the
very end or front of the spring choose a front spring that is correct for
your application
A short spring Ans✓✓✓Will be faster. That same spring but the higher
angle will be faster yet a lower angle makes it slower and softer hit
All metals are measured on the Ans✓✓✓Rockwell scale and find it best
to be 48-51
Remember no matter the spring length the screw should Ans✓✓✓Hit
the end of the spring
WITH DETAILED VERIFIED AND 100% ACCURATE
ANSWERS BRAND NEW EXAM ALREADY GRADED (A+
PASS)
A -bar Ans✓✓✓Armature bar 1.5 is standard length
When a bar is flat on front coil we are coil has between .010-.012
Ans✓✓✓Smaller creates more power it is noticeable (more coil is more
power)
You should be careful of small gaps as the air bar can hit the coil when
the machine is running Ans✓✓✓And this will cause it to rattle or
Deflection of the a bar. It will Make that a bar bounce off of the rear coil
and hit the front coil in correctly
Armature bar should be Ans✓✓✓Plain steel and no chrome. The coil
cord should not extend over coil cap very much coils with too much
Coors showing tend to run hot. Also they run sporadically after a short
time your machine can run in consistently and will require more voltage
to compensate
Push the a bar down on the front coil hold machine up to the light and
check Ans✓✓✓For dust Lent etc. this can cause your machine to rattle
and deflect believe it or not just blow debris with air can or pouty lips
Do not allow front spring to Ans✓✓✓Hangover the rear of the amateur
Bar this can create a buzz and undue birbration
, Armature bar rear and coil Ans✓✓✓Are aligned
A longer a bar extending past rear is fine Ans✓✓✓Creates a longer
stroke and usually a longer a bar and is 1.625 long
Angle of contact screws does not matter much Ans✓✓✓As long as it
turns on it's doing it's job however when the spring strikes the contact on
the up stroke the angle of the contact screw can have an effect of the
overall vibration of your machine.
Once your machine is set up correctly it should Ans✓✓✓The angle
should remain the same because the Contacts crew should head at the
very end or front of the spring choose a front spring that is correct for
your application
A short spring Ans✓✓✓Will be faster. That same spring but the higher
angle will be faster yet a lower angle makes it slower and softer hit
All metals are measured on the Ans✓✓✓Rockwell scale and find it best
to be 48-51
Remember no matter the spring length the screw should Ans✓✓✓Hit
the end of the spring
