Industrial Maintenance Technician Test
Exam 2026 Questions and Answers
Which device do you use to measure voltage? - Correct answer-Multi Meter
If you were asked to check out the I/O card on a plc, which card would you look
at? - Correct answer-Input Card
What does the term current refer to while dealing with electricity? - Correct
answer-Amps
On a hydraulic pump if you were told the pump is cavitating, what would you
check for? - Correct answer-Low fluid in the tank
In a 480 volt three phase system, what would your meter read if you went from one
leg to ground? - Correct answer-277
WHICH TOOL IS USED WHEN MEASURING SCREW PITCH - Correct
answer-Thread Gauge
What is a circuit breaker? - Correct answer-an automatically operated electrical
switch designed to protect an electrical circuit from damage caused by overload or
short circuit.
©COPYRIGHT 2025, ALL RIGHTS RESERVED 1
, What does a D.P.S.T. switch refer to? - Correct answer-double pole single throw
How many teeth are on a 40B12 sprocket? - Correct answer-12
The BCD equivalent of 1247 converts to_____. - Correct answer-0001 0010 0100
0111
What is the binary value of the following terms: Word and Nibble - Correct
answer-16 digit and 4 digit
What type of programming is used by PLCs. - Correct answer-ladder logic
What is the Octal and Hexadecimal= 0-9,A,B,C,D,E,F equivalent for the decimal
numbers 1-15 - Correct answer-0-7, 10-17, 20... and 0-9,A,B,C,D,E,F
Typical BCD input devices include ____. - Correct answer-thumbwheel switches
BCD code stands for _____. - Correct answer-binary coded decimal
The decimal 1000 has a Weighted Value Position of ______. - Correct answer-3
If in binary a zero signifies an OFF state a one signifies____________. - Correct
answer-an ON state
How many symbols are in the octal number system? - Correct answer-8
To convert from binary to octal, you select bits in groups of ____ - Correct answer-
3
©COPYRIGHT 2025, ALL RIGHTS RESERVED 2
Exam 2026 Questions and Answers
Which device do you use to measure voltage? - Correct answer-Multi Meter
If you were asked to check out the I/O card on a plc, which card would you look
at? - Correct answer-Input Card
What does the term current refer to while dealing with electricity? - Correct
answer-Amps
On a hydraulic pump if you were told the pump is cavitating, what would you
check for? - Correct answer-Low fluid in the tank
In a 480 volt three phase system, what would your meter read if you went from one
leg to ground? - Correct answer-277
WHICH TOOL IS USED WHEN MEASURING SCREW PITCH - Correct
answer-Thread Gauge
What is a circuit breaker? - Correct answer-an automatically operated electrical
switch designed to protect an electrical circuit from damage caused by overload or
short circuit.
©COPYRIGHT 2025, ALL RIGHTS RESERVED 1
, What does a D.P.S.T. switch refer to? - Correct answer-double pole single throw
How many teeth are on a 40B12 sprocket? - Correct answer-12
The BCD equivalent of 1247 converts to_____. - Correct answer-0001 0010 0100
0111
What is the binary value of the following terms: Word and Nibble - Correct
answer-16 digit and 4 digit
What type of programming is used by PLCs. - Correct answer-ladder logic
What is the Octal and Hexadecimal= 0-9,A,B,C,D,E,F equivalent for the decimal
numbers 1-15 - Correct answer-0-7, 10-17, 20... and 0-9,A,B,C,D,E,F
Typical BCD input devices include ____. - Correct answer-thumbwheel switches
BCD code stands for _____. - Correct answer-binary coded decimal
The decimal 1000 has a Weighted Value Position of ______. - Correct answer-3
If in binary a zero signifies an OFF state a one signifies____________. - Correct
answer-an ON state
How many symbols are in the octal number system? - Correct answer-8
To convert from binary to octal, you select bits in groups of ____ - Correct answer-
3
©COPYRIGHT 2025, ALL RIGHTS RESERVED 2
