OSHA Basic Orientation Plus Questions with 100% Verified Solutions

OSHA Basic Orientation Plus Questions with 100% Verified Solutions if you are replacing a piece of equipment the new one should be the same as the one being removed. If its not you should find out whether the change was on purpose. what is this called - ANSWER Management of change Used only where an immediate life threatening hazard exists - ANSWER Danger Used where immediate non life threatening hazards exist - ANSWER Warning Sign Used to warn against potential hazards or to caution against unsafe practices - ANSWER Caution signs Physical devices that are designed to prevent entry into an area where hazards are present. - ANSWER Barriers Obstacles that discourage the passage of persons or vehicles - ANSWER Barricade When lifting or setting down a load, bend at the - ANSWER Knees If you experience pain or discomfort as a result of your work activities, you should do what? - ANSWER report it to your supervisor as soon as possible What are the most common diseases caused by bloodborne pathogens in the workplace - ANSWER Human Immunodeficiency, Hepatitis B, Hepatitis C Universal precautions is an infection control approach where you treat all blood and body fluids as if they are known to be infectious for bloodborne pathogens only if the injured person is sick - ANSWER False What is the least severe rating in the GHS classification system - ANSWER Four What is the most severe rating in the GHS classification system - ANSWER One what does Hazard color RED means? - ANSWER Fire What does Hazard color BLUE means? - ANSWER Health What does Hazard color YELLOW mean? - ANSWER Reactivity What does Hazard color WHITE mean? - ANSWER Personal protection other hazards ans special precautions What does the HMIS color BLUE indicate? - ANSWER Health What does the HMIS color ORANGE indicate? - ANSWER Physical hazard What does the HMIS color RED indicate? - ANSWER Flammability What does the HMIS color WHITE indicate? - ANSWER Required personal protective equipment In what section of the SDS can you find the hazards of hydrogen sulfide - ANSWER Section 2 Which section of the SDS lists the measures should you take if exposed to hydrogen sulfide? - ANSWER section 4 Where in the SDS can you find what, if any, personal protective equipment (PPE) is required? - ANSWER Section 8 Physical/health hazards cause illness or injury - ANSWER True always test the atmosphere in the work area prior to starting the job when the site is greater than how many feet? - ANSWER four For an excavation that is 4 feet deep or more, egress points must be spaced no more than how many feet of lateral travel for employees? - ANSWER 25 narrow excavation made below the surface of the ground in which the depth is usually greater than the width and the width does not exceed how many fee? - ANSWER 15 What are the main methods for protecting workers from a cave-in - ANSWER Shielding, Sloping, shoring In an emergency you should call emergency response with the - ANSWER Exact location, number of victims Excavation measurements, special hazards at the location What elements are required in order for a fire to happen? - ANSWER Heat, fuel, oxygen What color does white represent under the NFPA label - ANSWER Other hazards and special precautions what is used on scaffolding after inspections are completed - ANSWER Scaffold tags what are base plates and mudsills used for? - ANSWER Distribute scaffold load weight What is performed regularly at job sites - ANSWER Inspections What are four main types of scaffolds - ANSWER Frame, rolling, tube, system A vertical barrier at floor level erected along exposed edges of a floor opening wall opening, platform, runway, or ramp to prevent falls of materials. - ANSWER Toe board what is an opening in the floor, platform or pavement measuring 12 inches or more and through which people may fall? - ANSWER Floor hole What is an opening in the floor, platform or pavement measuring less than 12 inches but more than one inch through which materials, but not people may fall called? - ANSWER Floor opening what is the first step in lockout/tagout to prevent the unexpected release of energy - ANSWER Preparation for shutdown What is the most frequently cited OSHA violation? - ANSWER Fall Protection What key elements are essential to recognizing hazards and reducing or eliminating workplace hazards? - ANSWER Management commitment and employee involvement You are encouraged to ask your coworkers/supervisor for information whenever you have a problem or are in doubt about what to do on a job? - ANSWER True It is your responsibility to follow all safety regulations, inform your employer of any unsafe condition; report all injuries no matter how minor they seem and wear the proper personal protective equipment? - ANSWER True The OSHA standard that addresses the requirements for preventing and lessening the results of a bad release of toxic, reactive, flammable, or highly explosive hazardous chemicals from a process - ANSWER Process safety management Standard The process Hazard Analysis (PHA) is one of the most important parts of the PSM program. PHAs are used to identify and evaluate major processes and ensure they are - ANSWER Evaluated, Controlled, and Identified In the PSM standard OSHA states employees must be trained if they work with highly hazardous chemicals. - ANSWER True