ACTUAL MAE 1351 EXAM 3 |2025-2026 LATEST UPDATED| REAL
EXAM QUESTIONS AND ANSWERS | 100% RATED CORRECT | 100%
VERFIED | ALREADY GRADED A+
What are some problems with pictorials? - (answer)the distortion of angles, the distortion of true
lengths, the distortion of Internal measurements, the distortion of curves
Then the general rule for presenting the object becomes: - (answer)"Start with the preferred
configuration; then add or subtract whatever views are necessary to best show all of the
geometry."
An axonometric drawing refers to three types of pictorial drawings: - (answer)isometric,
dimetric, and trimetric drawings
The absence of a second arrow is an indication that the cutting plane line is for a ____________
____________ - (answer)half section
Try drawing freehand a vertical line 5 inches long. Which direction did you follow? -
(answer)top to bottom
,A pictorial may be used as a formal engineering drawing of record. True? - (answer)No,
pictorials are for informal communication only
A fundamental problem with pictorials is that: - (answer)Angles and distances cannot be read
directly
SW can display an object in the following views: - (answer)isometric, perspective
My drawing axes for a 3D view are set such that the angles between them are as follows:
240,30,90 with one of the lines horizontal. The view is: - (answer)Cavalier
The same orthographic projection may be obtained from two different parts. True? -
(answer)Yes; two orthographic projections of completely different objects may look identical
A part may be properly represented on an engineering drawing with as few views as... -
(answer)one
The US standard for multiview orthographic projection is: - (answer)Third angle
, Germany - (answer)First angle
section lines are used to.... - (answer)improve the clarity of a section view by indicating the
portions of the part that had been solid at the location it was hypothetically cut
T/F the line thickness for the section line pattern is usually thicker than the part edges -
(answer)false
It is okay if the section line pattern is parallel or perpendicular to major features egdes -
(answer)no, this can cause confusion
T/F Offset sections can be considered modifications of full sections - (answer)true
An offset section... - (answer)allows multiple features, which normally require multiple section
views, to be captured on a single view
T/F Half sections do not save space or labor on an engineering drawing, especially for
symmetrical parts - (answer)false
EXAM QUESTIONS AND ANSWERS | 100% RATED CORRECT | 100%
VERFIED | ALREADY GRADED A+
What are some problems with pictorials? - (answer)the distortion of angles, the distortion of true
lengths, the distortion of Internal measurements, the distortion of curves
Then the general rule for presenting the object becomes: - (answer)"Start with the preferred
configuration; then add or subtract whatever views are necessary to best show all of the
geometry."
An axonometric drawing refers to three types of pictorial drawings: - (answer)isometric,
dimetric, and trimetric drawings
The absence of a second arrow is an indication that the cutting plane line is for a ____________
____________ - (answer)half section
Try drawing freehand a vertical line 5 inches long. Which direction did you follow? -
(answer)top to bottom
,A pictorial may be used as a formal engineering drawing of record. True? - (answer)No,
pictorials are for informal communication only
A fundamental problem with pictorials is that: - (answer)Angles and distances cannot be read
directly
SW can display an object in the following views: - (answer)isometric, perspective
My drawing axes for a 3D view are set such that the angles between them are as follows:
240,30,90 with one of the lines horizontal. The view is: - (answer)Cavalier
The same orthographic projection may be obtained from two different parts. True? -
(answer)Yes; two orthographic projections of completely different objects may look identical
A part may be properly represented on an engineering drawing with as few views as... -
(answer)one
The US standard for multiview orthographic projection is: - (answer)Third angle
, Germany - (answer)First angle
section lines are used to.... - (answer)improve the clarity of a section view by indicating the
portions of the part that had been solid at the location it was hypothetically cut
T/F the line thickness for the section line pattern is usually thicker than the part edges -
(answer)false
It is okay if the section line pattern is parallel or perpendicular to major features egdes -
(answer)no, this can cause confusion
T/F Offset sections can be considered modifications of full sections - (answer)true
An offset section... - (answer)allows multiple features, which normally require multiple section
views, to be captured on a single view
T/F Half sections do not save space or labor on an engineering drawing, especially for
symmetrical parts - (answer)false
