UPS MECHANICAL CRAFT TEST
QUESTIONS AND ANSWERS RATED
100% CORRECT
When working on an exchanger tube side hydro-test, the ____________________ best filling
point. answer - Channel Head
How many bolts need to be removed from a 12 bolt flange when installing gasket? answer - 5
One of the main factors to consider when installing an orifice plate is: answer - Direction of
Flow
When cutting a stud bolt, which end of the bolt should be saved? answer - All of the above
(Stamped, Stenciled, Marked)
The Method of pulling a rigging out of an exchanger bundle without equipment is called a
CONVENTIONAL pull answer - True
One of the most common internal components used to slow the ........ is called a Demister Pad
answer - True
Bundle straps should be aligned with the BAFFLE plates when rigging an exchanger bundle
answer - True
SOFTNERS should be out into place when chokers come into contact with sharp surfaces or
edges answer - True
, What are the two different classifications of manways on towers? answer - Both A an B
(Internal, External)
Which exchanger head is always absent on a U-Tube bundle? answer - Floating Head
A pipe union has a flow direction answer - True
To properly install a exchanger head and make sure the gasket seats properly you should.
answer - Glue Gasket to the proper gasket surface, where the gasket will catch ..... that gasket
surface preventing it from rolling
By order of hitch strenght, which is the correct order (strongest to weakest)? answer - Basket,
Vertical, Choke
You should first __________________ a spring before removing any piping or equipment
answer - Chock
Who gives the crane operator hand signals when performing a lift? answer - The person
assigned prior to the lift
The jib capacity is 8 tons and gthe ball weighs 900 lbs, what is the heaviest load that can be
lifted safely? answer - 15,100 lbs
You should start at the gap of a loose flange to complete a solid and square bolt up. answer - All
of the above (widest, biggest, largest)
When tightening a flange you should answer - Always use a star pattern
QUESTIONS AND ANSWERS RATED
100% CORRECT
When working on an exchanger tube side hydro-test, the ____________________ best filling
point. answer - Channel Head
How many bolts need to be removed from a 12 bolt flange when installing gasket? answer - 5
One of the main factors to consider when installing an orifice plate is: answer - Direction of
Flow
When cutting a stud bolt, which end of the bolt should be saved? answer - All of the above
(Stamped, Stenciled, Marked)
The Method of pulling a rigging out of an exchanger bundle without equipment is called a
CONVENTIONAL pull answer - True
One of the most common internal components used to slow the ........ is called a Demister Pad
answer - True
Bundle straps should be aligned with the BAFFLE plates when rigging an exchanger bundle
answer - True
SOFTNERS should be out into place when chokers come into contact with sharp surfaces or
edges answer - True
, What are the two different classifications of manways on towers? answer - Both A an B
(Internal, External)
Which exchanger head is always absent on a U-Tube bundle? answer - Floating Head
A pipe union has a flow direction answer - True
To properly install a exchanger head and make sure the gasket seats properly you should.
answer - Glue Gasket to the proper gasket surface, where the gasket will catch ..... that gasket
surface preventing it from rolling
By order of hitch strenght, which is the correct order (strongest to weakest)? answer - Basket,
Vertical, Choke
You should first __________________ a spring before removing any piping or equipment
answer - Chock
Who gives the crane operator hand signals when performing a lift? answer - The person
assigned prior to the lift
The jib capacity is 8 tons and gthe ball weighs 900 lbs, what is the heaviest load that can be
lifted safely? answer - 15,100 lbs
You should start at the gap of a loose flange to complete a solid and square bolt up. answer - All
of the above (widest, biggest, largest)
When tightening a flange you should answer - Always use a star pattern
