IPC A 610 Exam Questions with Complete Solutions Latest Update.
IPC A 610 Exam Questions with Complete Solutions Latest Update.
Class 1 Product - ✔✔✔General Electronics Product - includes products where
the major requirement is function of the completed assembly.
Class 2 Product - ✔✔✔Dedicated Service Electronic Product - Continued
performance and extended life required. Uninterrupted service is desired but
not required.
Class 3 Product - ✔✔✔High Performance Electrical Product - Continued high
performance or performance-on-demand is critical. Equipment downtime
cannot be tolerated. Equipment might be used for life-support or other
critical systems.
Who as the ultimate responsibility for identifying the class to which the
assembly is evaluated? - ✔✔✔The Customer.
Shall - ✔✔✔Invokes a requirement for manufacturers of all classes or
product, and failure to comply with the requirement is a noncompliance to
this standard.
Order of Precedence in event of conflict 1 - ✔✔✔1. Procurement as agreed
and documented between customer and supplier.
Order of Precedence in event of conflict 2 - ✔✔✔Master drawing or master
ass. drawing reflecting the customer's detailed requirements.
Order of Precedence in event of conflict 3 - ✔✔✔IPC-1-610 when invoked by
the customer or contract.
If documents other than IPC-A-610 are cited, the order of precedence shall be
defined in the _ - ✔✔✔Procurement documents
®™ pg. 1
, IPC A 610 Exam Questions with Complete Solutions Latest Update.
Target Condition - ✔✔✔A condition that is close to perfect, but is not always
achievable and may not be necessary to ensure the reliability of the
assembly.
Acceptable Condition - ✔✔✔A condition that, while not necessarily perfect,
will maintain integrity and reliability of the assembly
Defect Condition - ✔✔✔The form, fit or function of the assembly is
inadequate for use in its end use environment.
A defect for Class 1... - ✔✔✔automatically implies a defect for Class 2 and 3.
A defect for Class 2 implies a defect for Class 3.
Disposition - ✔✔✔The determination of how defects should be treated. These
include rework, use as is, scrap, and repair.
Who dispositions defect conditions? - ✔✔✔The manufacturer, based on
design, service and customer requirements.
Process Indicator Conditions - ✔✔✔A condition (not a defect) that does not
affect the form, fit or function of a product.
Process indicators should be... - ✔✔✔monitored as part of the process control
system
Is disposition of individual process indicators required? - ✔✔✔No, and
affected products should be used as-is.
®™ pg. 2
IPC A 610 Exam Questions with Complete Solutions Latest Update.
Class 1 Product - ✔✔✔General Electronics Product - includes products where
the major requirement is function of the completed assembly.
Class 2 Product - ✔✔✔Dedicated Service Electronic Product - Continued
performance and extended life required. Uninterrupted service is desired but
not required.
Class 3 Product - ✔✔✔High Performance Electrical Product - Continued high
performance or performance-on-demand is critical. Equipment downtime
cannot be tolerated. Equipment might be used for life-support or other
critical systems.
Who as the ultimate responsibility for identifying the class to which the
assembly is evaluated? - ✔✔✔The Customer.
Shall - ✔✔✔Invokes a requirement for manufacturers of all classes or
product, and failure to comply with the requirement is a noncompliance to
this standard.
Order of Precedence in event of conflict 1 - ✔✔✔1. Procurement as agreed
and documented between customer and supplier.
Order of Precedence in event of conflict 2 - ✔✔✔Master drawing or master
ass. drawing reflecting the customer's detailed requirements.
Order of Precedence in event of conflict 3 - ✔✔✔IPC-1-610 when invoked by
the customer or contract.
If documents other than IPC-A-610 are cited, the order of precedence shall be
defined in the _ - ✔✔✔Procurement documents
®™ pg. 1
, IPC A 610 Exam Questions with Complete Solutions Latest Update.
Target Condition - ✔✔✔A condition that is close to perfect, but is not always
achievable and may not be necessary to ensure the reliability of the
assembly.
Acceptable Condition - ✔✔✔A condition that, while not necessarily perfect,
will maintain integrity and reliability of the assembly
Defect Condition - ✔✔✔The form, fit or function of the assembly is
inadequate for use in its end use environment.
A defect for Class 1... - ✔✔✔automatically implies a defect for Class 2 and 3.
A defect for Class 2 implies a defect for Class 3.
Disposition - ✔✔✔The determination of how defects should be treated. These
include rework, use as is, scrap, and repair.
Who dispositions defect conditions? - ✔✔✔The manufacturer, based on
design, service and customer requirements.
Process Indicator Conditions - ✔✔✔A condition (not a defect) that does not
affect the form, fit or function of a product.
Process indicators should be... - ✔✔✔monitored as part of the process control
system
Is disposition of individual process indicators required? - ✔✔✔No, and
affected products should be used as-is.
®™ pg. 2
