B4: Study Questions
Study online at https://quizlet.com/_h1ha02
1. 1. Which of the following compo- Fender.
nents is the LEAST-Likely to be dam-
aged in a severe rear impact (A.
quarter panel, B. rear bumper, C.
center pillar, D. fender)?
2. 2. All of the following can be used to Hammer. Pneumatic knife, fine.
remove a windshield EXCEPT (A. fine
knife, b. Diano wire, C. pneumatic
knife, D. hammer)?
3. 3. What determines the welding Manufacturer's recommendations.
process used to make the repair (A.
manufacturer's recommendations,
B. shop procedures, C. tools avail-
able, D. technician's welding experi-
ence)?
4. 4. Technician A says that damaged Both A and B
side rails can be replaced. Tech-
nician B says that damaged cross
members can be replaced. Who is
right?
5. 5. What type of damage is present Sidesway. Sidesway changes the alignment to the cen-
if a vehicle's centerline is not with- ter of a damaged vehicle. A mash changes the length
in specifications (A. mash, B. sag, C. of a vehicle; sag and kickup change the height of a
sidesway, D. kickup)? vehicle.
6. 6. Technician A uses water to cool B only. The use of water to cool the hot metal could
metal that has been heated during lead to fatigue problems.
a repair. Technician B says to let the
metal cool naturally. Who is correct?
1/9
, B4: Study Questions
Study online at https://quizlet.com/_h1ha02
7. 7. What type or damage is found in Twist. Twist damage is corrected by pulling down on
the vehicles center section only (A. high corners of the center section and pushing up on
sag, B. twist, c. kickup, D. mash)? the low corners of the center section.
8. 8. How far should an insert extend, 6 inches. Manufacturer's specifications should be fol-
in either direction, from a crack in a lowed when inserts are used for frame repairs. The
frame rail (A. 2 inches, B. 4 inches, C. specifications from some manufacturers are 6 inches
6 inches, D. 8 inches)? in each direction for such a repair.
9. 9. Which of the following is the pneumatic knife. On modular glass, the molding is at-
best tool to use to remove modu- tached to the glass. To safely remove the glass without
lar glass without damage? (A. pneu- destroying the moldings, use a pneumatic knife with a
matic knife, B. fine knife, C. piano narrow blade to cut through the urethane seal that is
wire, D. hammer)? holding the glass in place.
10. 10. In Which of the following mea- strut tower gauge.
suring devices is the best to check
for misalignment of the spring tow-
ers (A. tram gauge, B. self-center-
ing gauges, C. strut tower gauge, D.
tape measure)?
11. 11.I Which of the following types of Diamond. Sag, twist, and kickup damage are diag-
frame damage is identified with a nosed using gauges. Diamond damage is measured
tram gauge (A. sag, B. diamond, C. using a tram gauge. Refer to the manufacturer's refer-
twist, D. kickup)? ence manuals when taking measurements. Diamond
condition can be diagnosed by cross- or X-checking on
the frame members.
12. 12. The process of welding two Butt Weld. Butt welds are performed by welding the
edges of adjacent panels together, edges of two adjacent panels.
2/9
Study online at https://quizlet.com/_h1ha02
1. 1. Which of the following compo- Fender.
nents is the LEAST-Likely to be dam-
aged in a severe rear impact (A.
quarter panel, B. rear bumper, C.
center pillar, D. fender)?
2. 2. All of the following can be used to Hammer. Pneumatic knife, fine.
remove a windshield EXCEPT (A. fine
knife, b. Diano wire, C. pneumatic
knife, D. hammer)?
3. 3. What determines the welding Manufacturer's recommendations.
process used to make the repair (A.
manufacturer's recommendations,
B. shop procedures, C. tools avail-
able, D. technician's welding experi-
ence)?
4. 4. Technician A says that damaged Both A and B
side rails can be replaced. Tech-
nician B says that damaged cross
members can be replaced. Who is
right?
5. 5. What type of damage is present Sidesway. Sidesway changes the alignment to the cen-
if a vehicle's centerline is not with- ter of a damaged vehicle. A mash changes the length
in specifications (A. mash, B. sag, C. of a vehicle; sag and kickup change the height of a
sidesway, D. kickup)? vehicle.
6. 6. Technician A uses water to cool B only. The use of water to cool the hot metal could
metal that has been heated during lead to fatigue problems.
a repair. Technician B says to let the
metal cool naturally. Who is correct?
1/9
, B4: Study Questions
Study online at https://quizlet.com/_h1ha02
7. 7. What type or damage is found in Twist. Twist damage is corrected by pulling down on
the vehicles center section only (A. high corners of the center section and pushing up on
sag, B. twist, c. kickup, D. mash)? the low corners of the center section.
8. 8. How far should an insert extend, 6 inches. Manufacturer's specifications should be fol-
in either direction, from a crack in a lowed when inserts are used for frame repairs. The
frame rail (A. 2 inches, B. 4 inches, C. specifications from some manufacturers are 6 inches
6 inches, D. 8 inches)? in each direction for such a repair.
9. 9. Which of the following is the pneumatic knife. On modular glass, the molding is at-
best tool to use to remove modu- tached to the glass. To safely remove the glass without
lar glass without damage? (A. pneu- destroying the moldings, use a pneumatic knife with a
matic knife, B. fine knife, C. piano narrow blade to cut through the urethane seal that is
wire, D. hammer)? holding the glass in place.
10. 10. In Which of the following mea- strut tower gauge.
suring devices is the best to check
for misalignment of the spring tow-
ers (A. tram gauge, B. self-center-
ing gauges, C. strut tower gauge, D.
tape measure)?
11. 11.I Which of the following types of Diamond. Sag, twist, and kickup damage are diag-
frame damage is identified with a nosed using gauges. Diamond damage is measured
tram gauge (A. sag, B. diamond, C. using a tram gauge. Refer to the manufacturer's refer-
twist, D. kickup)? ence manuals when taking measurements. Diamond
condition can be diagnosed by cross- or X-checking on
the frame members.
12. 12. The process of welding two Butt Weld. Butt welds are performed by welding the
edges of adjacent panels together, edges of two adjacent panels.
2/9
