Structural Analysis And Damage Repair
Study online at https://quizlet.com/_82oq5t
1. technician A says that the weight of C
the mechanical and drivetrain com- The weight of the mechanical and drivetrain compo-
ponents must be taken into account nents do need to be considered when measuring a
when measuring the unibody. Tech unibody and some information providers do provide
B says that some dimensional man- mechanicals and engine out specifications.
uals provise measurements for me-
chanicals out or compensated for.
Who is right?
A. Tech A only
B. Tech B only
C. Both A & B
D. Neither
2. Tech A says that the datum plane is D
established by identifying the vehi- The datum plane is an imaginary plane under the
cle centerline. Tech B says that width vehicle from which height measurements are made.
mesurements are made from the Width measurements are made from the centerline of
datum plane. who is right? the vehicle.
A.Tech A only
B. Tech B only
C. Both A & B
D.Neither
3. Tech A says that there are two basic C
full frame designs. Tech B says that There are two primary full frame designs, the ladder
there are three rail configurations. and perimeter. There are three basic full frame rail
who is right? configurations; open 'C' Channel, Closed 'C' Channel
A. Tech A and Box frames.
B. Tech B
C. Both A & B
D. Neither
, Structural Analysis And Damage Repair
Study online at https://quizlet.com/_82oq5t
4. While measuring a unibody vehicle B
it is discovered the left front rail is Width is calculated from the center out. So a value of
-111mm from specification in width. -111mm on the left rail shows sway to the right and in
Technician A says that the vehicle is toward centerline.
swayed to the left. Tech B says that
the vehicle is in toward centerline.
who is right?
A. Tech A
B. Tech B
C. Both
D. Neither
5. Tech A says that measurements that B
are the same on both sides of the Asymmetrical measurements are different on opposite
vehicle are known as asymmetrical. sides of the vehicle. Symmetrical measurements are
Tech B says that the dimension man- the same on both sides.
ual should be checked to see how
asymmetrical dimensions are not-
ed. who is right?
A. Tech A
B. Tech B
C. Both
D. Neither
6. A unibody vehicle that was in a colli- A
sion has been repaired. a four wheel A unibody can be seriously damaged and out of align-
alignment shows that the car is ment in terms of factory specs. however, if the control
tracking within manufacture specs, points and suspension mounting points are within the
but a visual inspection of the car re- spec, the wheel alignment will be normal. this does not
veals some misalignment with pan- mean the car is repaired properly, although the saftey
els. could the unibody still be bent? of the car can only be ascertained on an individual
A. Yes basis.
Study online at https://quizlet.com/_82oq5t
1. technician A says that the weight of C
the mechanical and drivetrain com- The weight of the mechanical and drivetrain compo-
ponents must be taken into account nents do need to be considered when measuring a
when measuring the unibody. Tech unibody and some information providers do provide
B says that some dimensional man- mechanicals and engine out specifications.
uals provise measurements for me-
chanicals out or compensated for.
Who is right?
A. Tech A only
B. Tech B only
C. Both A & B
D. Neither
2. Tech A says that the datum plane is D
established by identifying the vehi- The datum plane is an imaginary plane under the
cle centerline. Tech B says that width vehicle from which height measurements are made.
mesurements are made from the Width measurements are made from the centerline of
datum plane. who is right? the vehicle.
A.Tech A only
B. Tech B only
C. Both A & B
D.Neither
3. Tech A says that there are two basic C
full frame designs. Tech B says that There are two primary full frame designs, the ladder
there are three rail configurations. and perimeter. There are three basic full frame rail
who is right? configurations; open 'C' Channel, Closed 'C' Channel
A. Tech A and Box frames.
B. Tech B
C. Both A & B
D. Neither
, Structural Analysis And Damage Repair
Study online at https://quizlet.com/_82oq5t
4. While measuring a unibody vehicle B
it is discovered the left front rail is Width is calculated from the center out. So a value of
-111mm from specification in width. -111mm on the left rail shows sway to the right and in
Technician A says that the vehicle is toward centerline.
swayed to the left. Tech B says that
the vehicle is in toward centerline.
who is right?
A. Tech A
B. Tech B
C. Both
D. Neither
5. Tech A says that measurements that B
are the same on both sides of the Asymmetrical measurements are different on opposite
vehicle are known as asymmetrical. sides of the vehicle. Symmetrical measurements are
Tech B says that the dimension man- the same on both sides.
ual should be checked to see how
asymmetrical dimensions are not-
ed. who is right?
A. Tech A
B. Tech B
C. Both
D. Neither
6. A unibody vehicle that was in a colli- A
sion has been repaired. a four wheel A unibody can be seriously damaged and out of align-
alignment shows that the car is ment in terms of factory specs. however, if the control
tracking within manufacture specs, points and suspension mounting points are within the
but a visual inspection of the car re- spec, the wheel alignment will be normal. this does not
veals some misalignment with pan- mean the car is repaired properly, although the saftey
els. could the unibody still be bent? of the car can only be ascertained on an individual
A. Yes basis.
