Texas Wastewater Class C Exam with Test Bank Questions and
100% Correct Answers Latest Update 2025
The Activated Sludge Process:
A. requires preaeration
B. requires Activated Carbon
C. is an aerobic biological process.
D. Usually precedes primary sedimentation.
E. Requires 50% by volume old sludge to work effectively.
C. Is an Aerobic biological process
A complete mix activated sludge plant has a fast settling sludge and high
amounts of pin floc leaving the clarifier. One way to correct this problem
is to :
A. Increase the RAS Flow
B. Reduce Wasting Rates
C. Increase dissolved oxygen levels.
D. Increase the F/M ratio by wasting more
E. Increase the sludge age by wasting less.
D. Increase the F/M Ratio by Wasting More
Which of the following flow rates should be measured if the operator is to
control plant properly?
A. Aeration rate or resulting dissolved oxygen level.
B. Influent or effluent.
C. return sludge
D. waste sludge
E. all the above
E. all the above
During start up your aeration tank produces excessive amounts of billowing
white foam. This can be corrected by:
A. Doing nothing, it will go away in a few hours
B. Increasing the sludge wasting rate
C. Seeding the process with sufficient good quality sludge
D. Spraying water on the foam until it is gone
, Texas Wastewater Class C Exam with Test Bank Questions and
100% Correct Answers Latest Update 2025
E. Taking a weeks vacation
C. Seeding the process with sufficient good quality sludge
In solving an operational problem at a treatment plant:
A. there is almost always a good technical solution. It may require
considerable experience and time to learn whaat it is.
B. Human errors have to be corrected since the operator is at fault.
C. don't let the laboratory personnel influence you're judgement as to what
the best solution is.
D. standard textbooks in sanitary engineering are the best source of
information.
E. It is best to do nothing until the TNRCCC sends a violation notice.
A. there is almost always a good technical solution. It may require
considerable experience and time to learn whaat it is.
When the return sludge rate is too low, what happens?
A. the aeration tank will not fill
B. There will be insufficient organisms to treat the wast load entering the
aeration basin
C. the activated sludge in the aerator will starve.
D. the sludge blanket in the secondary clarifier could become too high.
E. B and D
E. B and D
What factors affect how well the mixed liquor suspended solids settle in
the final clarifier?
A. flow velocity and or turbulence
B. temperature
C. quality of the mixed liquor solids
D. Short circuiting
E. All of the above
E. All of the above
100% Correct Answers Latest Update 2025
The Activated Sludge Process:
A. requires preaeration
B. requires Activated Carbon
C. is an aerobic biological process.
D. Usually precedes primary sedimentation.
E. Requires 50% by volume old sludge to work effectively.
C. Is an Aerobic biological process
A complete mix activated sludge plant has a fast settling sludge and high
amounts of pin floc leaving the clarifier. One way to correct this problem
is to :
A. Increase the RAS Flow
B. Reduce Wasting Rates
C. Increase dissolved oxygen levels.
D. Increase the F/M ratio by wasting more
E. Increase the sludge age by wasting less.
D. Increase the F/M Ratio by Wasting More
Which of the following flow rates should be measured if the operator is to
control plant properly?
A. Aeration rate or resulting dissolved oxygen level.
B. Influent or effluent.
C. return sludge
D. waste sludge
E. all the above
E. all the above
During start up your aeration tank produces excessive amounts of billowing
white foam. This can be corrected by:
A. Doing nothing, it will go away in a few hours
B. Increasing the sludge wasting rate
C. Seeding the process with sufficient good quality sludge
D. Spraying water on the foam until it is gone
, Texas Wastewater Class C Exam with Test Bank Questions and
100% Correct Answers Latest Update 2025
E. Taking a weeks vacation
C. Seeding the process with sufficient good quality sludge
In solving an operational problem at a treatment plant:
A. there is almost always a good technical solution. It may require
considerable experience and time to learn whaat it is.
B. Human errors have to be corrected since the operator is at fault.
C. don't let the laboratory personnel influence you're judgement as to what
the best solution is.
D. standard textbooks in sanitary engineering are the best source of
information.
E. It is best to do nothing until the TNRCCC sends a violation notice.
A. there is almost always a good technical solution. It may require
considerable experience and time to learn whaat it is.
When the return sludge rate is too low, what happens?
A. the aeration tank will not fill
B. There will be insufficient organisms to treat the wast load entering the
aeration basin
C. the activated sludge in the aerator will starve.
D. the sludge blanket in the secondary clarifier could become too high.
E. B and D
E. B and D
What factors affect how well the mixed liquor suspended solids settle in
the final clarifier?
A. flow velocity and or turbulence
B. temperature
C. quality of the mixed liquor solids
D. Short circuiting
E. All of the above
E. All of the above
