Alberta welding first year final AIT exam Latest
Update 2025-2026 85 Questions and 100%
Verified Correct Answers Guaranteed A+
"Nesting" in GMAW wire feeder can be caused by: - CORRECT ANSWER: drive roll
pressure is set to high
A Material Safety Data Sheet must be reviewed whenever new information becomes
available or at least how often? - CORRECT ANSWER: every three years
A small change in sling angle can drastically affect the: - CORRECT ANSWER: sling
load.
A steamed vessel is safest to weld on when it is cooled down to room temperature . -
CORRECT ANSWER: False
DCEN is also refereed to as: - CORRECT ANSWER: Straight polarity
Excessive penetration on a root pass would likely be caused by: - CORRECT ANSWER:
travel speeds too low.
Flame propagation means the speed at which the fuel gas will travel - CORRECT
ANSWER: False
Grossly unequal pressure of gases may cause a: - CORRECT ANSWER: flashback.
How are corrections or revisions indicated on a drawing? - CORRECT ANSWER:
Numbers or letters that have a circle or triangle drawn around them
, How is the size of an equal leg fillet weld determined? - CORRECT ANSWER: Leg
length of the largest equal leg triangle
How is the size of an unequal leg fillet weld determined? - CORRECT ANSWER: By the
length of its shortest leg
How is the strength of a fillet weld determined? - CORRECT ANSWER: Effective throat
dimension
How much electrode stickout is recommended when using gas shielded FCAW with 1.2
mm (0.045") wire? - CORRECT ANSWER: 10 mm to 19 mm (3/8" to 3/4")
How much electrode stickout is recommended when using gas shielded FCAW with 1.2
mm (0.045") wire? - CORRECT ANSWER: 10 mm to 19 mm (3/8" to 3/4")
How often must you inspect your fall arrest equipment? - CORRECT ANSWER: before
use on each shift
If you must apply force to a suspended load, always pull the load towards you. -
CORRECT ANSWER:
In common fabricating practice, there are how many basic joint types? - CORRECT
ANSWER: 5
In the AWS designation ER70T-6, the digit '0' would tell you that: - CORRECT
ANSWER: This is a flat and horizontal filler metal
In the CSA classification for the F49AZ-EM14K flux/wire designation what does the "14"
stand for? - CORRECT ANSWER: 0.14% carbon content
Update 2025-2026 85 Questions and 100%
Verified Correct Answers Guaranteed A+
"Nesting" in GMAW wire feeder can be caused by: - CORRECT ANSWER: drive roll
pressure is set to high
A Material Safety Data Sheet must be reviewed whenever new information becomes
available or at least how often? - CORRECT ANSWER: every three years
A small change in sling angle can drastically affect the: - CORRECT ANSWER: sling
load.
A steamed vessel is safest to weld on when it is cooled down to room temperature . -
CORRECT ANSWER: False
DCEN is also refereed to as: - CORRECT ANSWER: Straight polarity
Excessive penetration on a root pass would likely be caused by: - CORRECT ANSWER:
travel speeds too low.
Flame propagation means the speed at which the fuel gas will travel - CORRECT
ANSWER: False
Grossly unequal pressure of gases may cause a: - CORRECT ANSWER: flashback.
How are corrections or revisions indicated on a drawing? - CORRECT ANSWER:
Numbers or letters that have a circle or triangle drawn around them
, How is the size of an equal leg fillet weld determined? - CORRECT ANSWER: Leg
length of the largest equal leg triangle
How is the size of an unequal leg fillet weld determined? - CORRECT ANSWER: By the
length of its shortest leg
How is the strength of a fillet weld determined? - CORRECT ANSWER: Effective throat
dimension
How much electrode stickout is recommended when using gas shielded FCAW with 1.2
mm (0.045") wire? - CORRECT ANSWER: 10 mm to 19 mm (3/8" to 3/4")
How much electrode stickout is recommended when using gas shielded FCAW with 1.2
mm (0.045") wire? - CORRECT ANSWER: 10 mm to 19 mm (3/8" to 3/4")
How often must you inspect your fall arrest equipment? - CORRECT ANSWER: before
use on each shift
If you must apply force to a suspended load, always pull the load towards you. -
CORRECT ANSWER:
In common fabricating practice, there are how many basic joint types? - CORRECT
ANSWER: 5
In the AWS designation ER70T-6, the digit '0' would tell you that: - CORRECT
ANSWER: This is a flat and horizontal filler metal
In the CSA classification for the F49AZ-EM14K flux/wire designation what does the "14"
stand for? - CORRECT ANSWER: 0.14% carbon content
