Michigan State Brakes Certification Exam
with accurate questions and verified
answers
Most 1995 & newer vehicles use which of the following types of wheels
bearings on non-drive wheel? - ANSWER>>Sealed non-serviceable
to test a vacuum power brake booster in the vehicle, you should pump the
brake pedal at least 4 times, hold the brake pedal depressed, and start the
engine. the brake pedal should: - ANSWER>>drop slightly and remain firm
You are installing a set of brake shoe linings that are not the same length.
Traditionally, the primary shoe lining is: - ANSWER>>Smaller and goes
towards the front of the car.
A cracked or torn vacuum diaphragm in a brake power booster would most
likely cause: - ANSWER>>a hard pedal feel requiring very high pedal effort
to stop
A mechanic finds gear lube inside both rear brake drums on a rear wheel
drive vehicle. What is the most likely cause of this problem? - ANSWER>>A
plugged axle
Which of the following incorrect service procedures will cause brake lock-
up? - ANSWER>>master cylinder push rod adjusted too long
, Which of the following describes the proper way to depressurized an ABS
system? - ANSWER>>Pump the brake pedal at least 25 times (or more,
depending on the manufacturer's recommendation) with the ignition off.
The rear brakes are dragging after having new linings installed and the
drums machined. the most likely cause is the: - ANSWER>>technician use
the parking brake to adjust shoes and the cable is stuck
When turning brake drums: - ANSWER>>use a dampening strap to reduce
chatter
Which of the following is NOT a necessary drum brake measurement? -
ANSWER>>run-out
On a 3-channel system, which wheels are on the same circuit? -
ANSWER>>both rear wheels
One way to test an ABS wheel speed signal is to use _____ on your digital
multimeter. - ANSWER>>AC volts
The key input for the ABS control module comes from the: -
ANSWER>>wheel speed sensors
ABS speed sensor and sensor rings: - ANSWER>>should not be hammered
or tapped on and should always be replaced as a matched set
Flexible brake hoses should be replaced: - ANSWER>>when dampness is
evident on the hose
with accurate questions and verified
answers
Most 1995 & newer vehicles use which of the following types of wheels
bearings on non-drive wheel? - ANSWER>>Sealed non-serviceable
to test a vacuum power brake booster in the vehicle, you should pump the
brake pedal at least 4 times, hold the brake pedal depressed, and start the
engine. the brake pedal should: - ANSWER>>drop slightly and remain firm
You are installing a set of brake shoe linings that are not the same length.
Traditionally, the primary shoe lining is: - ANSWER>>Smaller and goes
towards the front of the car.
A cracked or torn vacuum diaphragm in a brake power booster would most
likely cause: - ANSWER>>a hard pedal feel requiring very high pedal effort
to stop
A mechanic finds gear lube inside both rear brake drums on a rear wheel
drive vehicle. What is the most likely cause of this problem? - ANSWER>>A
plugged axle
Which of the following incorrect service procedures will cause brake lock-
up? - ANSWER>>master cylinder push rod adjusted too long
, Which of the following describes the proper way to depressurized an ABS
system? - ANSWER>>Pump the brake pedal at least 25 times (or more,
depending on the manufacturer's recommendation) with the ignition off.
The rear brakes are dragging after having new linings installed and the
drums machined. the most likely cause is the: - ANSWER>>technician use
the parking brake to adjust shoes and the cable is stuck
When turning brake drums: - ANSWER>>use a dampening strap to reduce
chatter
Which of the following is NOT a necessary drum brake measurement? -
ANSWER>>run-out
On a 3-channel system, which wheels are on the same circuit? -
ANSWER>>both rear wheels
One way to test an ABS wheel speed signal is to use _____ on your digital
multimeter. - ANSWER>>AC volts
The key input for the ABS control module comes from the: -
ANSWER>>wheel speed sensors
ABS speed sensor and sensor rings: - ANSWER>>should not be hammered
or tapped on and should always be replaced as a matched set
Flexible brake hoses should be replaced: - ANSWER>>when dampness is
evident on the hose
