Gold Coast Cards Exam Questions With Accurate Solutions.
The minimum slope for lapped non soldered metal seam roof with applied lap
sealant shall be; - accurate answer-1/2:12 lapped non soldered metal seam
roof.
The maximum intended load for a pump jack scaffold shall be 500lbs between
poles. - accurate answer-scaffold shall be 500 lbs between poles.
Lap joints should not be used on gravel stops where the face exceeds 4 -
accurate answer-4
The minimum size straps for a stainless steel gutter 18'' wide should be 1/8 x
1 - accurate answer-1/8 x 1
The maximum temperature for mop applications of Type III asphalt, with a
EVT value of 125 cP is 430 degrees F. - accurate answer-430
The minimum number of fastener require per cleat per pan in a standing seam
roof installation is 2 - accurate answer-2
What type of asphalt should be used to install an SBS modified bitumen
membrane on a 4:12 roof slope? Type IV - accurate answer-IV
NRCA recommends to maintain the kettle and tanker temperatures less than
25 degrees F below the actual flash point of the material used - accurate
answer-25
Asphalt shingles shall be secured to the roof with not less than 4 fasteners per
strip single - accurate answer-4
Liquid applied roofs shall have a design slope of a minimum of 1/4: 12 -
accurate answer-1/4:12
Per NRCA, how many pieces per square are there in common interlocking tiles
with an overall dimension of. 14x 9 inches, an an exposure of 11 x 8-1/4
inches? 158 - accurate answer-158
, Polyvinyl chloride membrane should conform to ASTM D4434 - accurate
answer-D4434
1 perm equals 1 grain - accurate answer-1 grain
How many plies of coal tar built membrane are needed to waterproof a wall
when the hydrostatics pressure head is 49? 5 - accurate answer-5
In HVHZ, metal counter flashing shall be side lapped a minimum of 4 inches -
accurate answer-4 inches
The R value for special Kraft faced batt insulation 6 1/4 thick for ceiling is 19 -
accurate answer-19
Hot roofing is responsible for at least 23% of all roofing injuries. - accurate
answer-23% of all roofing injuries.
NRCA recommends that fiberglass reinforced asphalt shingles comply with
ASTM standard D3462 - accurate answer-D3462
Per NRCA, 1 square of 16" x 9" slates installed with a 3" lap will require 246
pieces - accurate answer-246 pieces
Effective September 2, 1997, the employer shall have a competent person
determine the feasibility and safety of providing fall. Protection for employees
erecting or dismantling supported scaffolds. Competent person - accurate
answer-Competent person.
In a close cut valley, in addition to the required felt underlayment, flash the
valley with a 36" wide layer of # 15 or # 30 asphalt saturated felt. - accurate
answer-36" wide layer of #15 or #30 asphalt saturated felt.
Never apply EPDM roofing t any roof that is subject to chemical discharge or
covering a cold storage or freezer facility. - accurate answer-EPDM
The minimum gauge for galvanized steel flashing receiver is 26 gauge. -
accurate answer-26 gauge.
The minimum slope for lapped non soldered metal seam roof with applied lap
sealant shall be; - accurate answer-1/2:12 lapped non soldered metal seam
roof.
The maximum intended load for a pump jack scaffold shall be 500lbs between
poles. - accurate answer-scaffold shall be 500 lbs between poles.
Lap joints should not be used on gravel stops where the face exceeds 4 -
accurate answer-4
The minimum size straps for a stainless steel gutter 18'' wide should be 1/8 x
1 - accurate answer-1/8 x 1
The maximum temperature for mop applications of Type III asphalt, with a
EVT value of 125 cP is 430 degrees F. - accurate answer-430
The minimum number of fastener require per cleat per pan in a standing seam
roof installation is 2 - accurate answer-2
What type of asphalt should be used to install an SBS modified bitumen
membrane on a 4:12 roof slope? Type IV - accurate answer-IV
NRCA recommends to maintain the kettle and tanker temperatures less than
25 degrees F below the actual flash point of the material used - accurate
answer-25
Asphalt shingles shall be secured to the roof with not less than 4 fasteners per
strip single - accurate answer-4
Liquid applied roofs shall have a design slope of a minimum of 1/4: 12 -
accurate answer-1/4:12
Per NRCA, how many pieces per square are there in common interlocking tiles
with an overall dimension of. 14x 9 inches, an an exposure of 11 x 8-1/4
inches? 158 - accurate answer-158
, Polyvinyl chloride membrane should conform to ASTM D4434 - accurate
answer-D4434
1 perm equals 1 grain - accurate answer-1 grain
How many plies of coal tar built membrane are needed to waterproof a wall
when the hydrostatics pressure head is 49? 5 - accurate answer-5
In HVHZ, metal counter flashing shall be side lapped a minimum of 4 inches -
accurate answer-4 inches
The R value for special Kraft faced batt insulation 6 1/4 thick for ceiling is 19 -
accurate answer-19
Hot roofing is responsible for at least 23% of all roofing injuries. - accurate
answer-23% of all roofing injuries.
NRCA recommends that fiberglass reinforced asphalt shingles comply with
ASTM standard D3462 - accurate answer-D3462
Per NRCA, 1 square of 16" x 9" slates installed with a 3" lap will require 246
pieces - accurate answer-246 pieces
Effective September 2, 1997, the employer shall have a competent person
determine the feasibility and safety of providing fall. Protection for employees
erecting or dismantling supported scaffolds. Competent person - accurate
answer-Competent person.
In a close cut valley, in addition to the required felt underlayment, flash the
valley with a 36" wide layer of # 15 or # 30 asphalt saturated felt. - accurate
answer-36" wide layer of #15 or #30 asphalt saturated felt.
Never apply EPDM roofing t any roof that is subject to chemical discharge or
covering a cold storage or freezer facility. - accurate answer-EPDM
The minimum gauge for galvanized steel flashing receiver is 26 gauge. -
accurate answer-26 gauge.
