NOCTI NOTAS
1. Select the steps that are in the correct order to prepare a technical report
1. Gather data, analyze results, outline report, write draft, and revise draft.
2. Outline report, analyze results, gather data, write draft, and revise draft
3. Outline report, gather data, analyze results, write draft, revise draft.
4. Gather data, write draft, analyze results, outline report, revise draft.
2. Which of the following tools is designed to measure the specific degree of tightness of
nuts or bolts?
1. Pipe wrench
2. Reamer
3. Torque wrench
4. Open end wrench
3. The amount of heat required to raise the temperature of one pound of water by one
degree Fahrenheit is
1. One calorie
2. One joule
3. One BTU
4. One foot pound
1. Why is evaluation an important step in the design process?
1. It helps determine whether the design is valid
2. It provides a cost analysis
3. The product can be sold based on the outcome
4. The product design is easier to reproduce
5. Properties of common _____ materials are divided into the following categories: physical,
mechanical, thermal, electric, and acoustic.
1. Rigid
2. Liquid
3. Solid
4. Gaseous
6. When measuring current, the meter should be connected in
1. Reverse Engineering
2. Series
3. Series Parallel
4. Parallel
,7. Oily and paint-covered rags should be disposed of:
1. Outside the building
2. In a paper bag
3. In a metal safety can
4. In a bucket
8. Consensus is
1. Agreeing on a proposed solution
2. Disagreeing on a proposed solution
3. Reviewing the proposal solution
4. Participating in the census
9. The AC Voltage waveform is called a _____ wave
1. Cosin
2. Full
3. Sin
4. Half
10. Which of the following adversely affects the strength of materials?
1. Barometric Pressure
2. Stains
3. Altitude
4. Corrosion
11. A water distribution system includes a storage tank located at the top of a tower. Which of
the following configurations would provide the most pressure?
1. 100 feet high town, 3500 gallon tank
2. 110 feet high tower, 2500 gallon tank
3. 120 feet high tower, 2500 gallon tank
4. 125 feet high tower, 1000 gallon tank
12. Which of the following is used to denote the center of a circle?
1. S
2. **
3. +
4. =
13. If a wooden box weighing 50 pounds is placed on a flat wooden table and the force required
to move the box is 37 pounds, the coefficient of friction is
1. .74
2. .49
, 3. .53
4. 1.3
14. Heat moving through space without the assistance of a physical substance is known as
1. Conduction
2. Convection
3. Friction
4. Radiation
15. Immediately report the malfunction of any piece of equipment to:
1. Other employees
2. A safety engineer
3. The supervisor
4. OSHA
16. Bolts and screws should be designed by the following data in which sequence shown
below?
1. Product name, nominal size, material and finish, product length for bolts and
screws, and threads per inch.
2. Nominal size, threads per inch, product length for bolts and screws, product
name, and material and finish.
3. Material and finish, nominal size, product name, threads per inch, and product
length for bolts and screws.
4. Product length for bolts and screws, material and finish, threads per inch, and
product size.
17. Atmospheric pressure at sea level is
1. 3.14 psi
2. 14.7 psi
3. 29.92 psi
4. 114.71 psi
18. The primary function of the fuse(s) in a circuit should be to
1. Prevent motor overload
2. Protect the step-down transformer
3. Protect from open circuits
4. Prevent single-phasing of the motor
19. The technician should use a _____ to cut a keyway in a shaft.
1. Milling machine
2. Lathe
3. Jig gritter
4. Surface Grinder
1. Select the steps that are in the correct order to prepare a technical report
1. Gather data, analyze results, outline report, write draft, and revise draft.
2. Outline report, analyze results, gather data, write draft, and revise draft
3. Outline report, gather data, analyze results, write draft, revise draft.
4. Gather data, write draft, analyze results, outline report, revise draft.
2. Which of the following tools is designed to measure the specific degree of tightness of
nuts or bolts?
1. Pipe wrench
2. Reamer
3. Torque wrench
4. Open end wrench
3. The amount of heat required to raise the temperature of one pound of water by one
degree Fahrenheit is
1. One calorie
2. One joule
3. One BTU
4. One foot pound
1. Why is evaluation an important step in the design process?
1. It helps determine whether the design is valid
2. It provides a cost analysis
3. The product can be sold based on the outcome
4. The product design is easier to reproduce
5. Properties of common _____ materials are divided into the following categories: physical,
mechanical, thermal, electric, and acoustic.
1. Rigid
2. Liquid
3. Solid
4. Gaseous
6. When measuring current, the meter should be connected in
1. Reverse Engineering
2. Series
3. Series Parallel
4. Parallel
,7. Oily and paint-covered rags should be disposed of:
1. Outside the building
2. In a paper bag
3. In a metal safety can
4. In a bucket
8. Consensus is
1. Agreeing on a proposed solution
2. Disagreeing on a proposed solution
3. Reviewing the proposal solution
4. Participating in the census
9. The AC Voltage waveform is called a _____ wave
1. Cosin
2. Full
3. Sin
4. Half
10. Which of the following adversely affects the strength of materials?
1. Barometric Pressure
2. Stains
3. Altitude
4. Corrosion
11. A water distribution system includes a storage tank located at the top of a tower. Which of
the following configurations would provide the most pressure?
1. 100 feet high town, 3500 gallon tank
2. 110 feet high tower, 2500 gallon tank
3. 120 feet high tower, 2500 gallon tank
4. 125 feet high tower, 1000 gallon tank
12. Which of the following is used to denote the center of a circle?
1. S
2. **
3. +
4. =
13. If a wooden box weighing 50 pounds is placed on a flat wooden table and the force required
to move the box is 37 pounds, the coefficient of friction is
1. .74
2. .49
, 3. .53
4. 1.3
14. Heat moving through space without the assistance of a physical substance is known as
1. Conduction
2. Convection
3. Friction
4. Radiation
15. Immediately report the malfunction of any piece of equipment to:
1. Other employees
2. A safety engineer
3. The supervisor
4. OSHA
16. Bolts and screws should be designed by the following data in which sequence shown
below?
1. Product name, nominal size, material and finish, product length for bolts and
screws, and threads per inch.
2. Nominal size, threads per inch, product length for bolts and screws, product
name, and material and finish.
3. Material and finish, nominal size, product name, threads per inch, and product
length for bolts and screws.
4. Product length for bolts and screws, material and finish, threads per inch, and
product size.
17. Atmospheric pressure at sea level is
1. 3.14 psi
2. 14.7 psi
3. 29.92 psi
4. 114.71 psi
18. The primary function of the fuse(s) in a circuit should be to
1. Prevent motor overload
2. Protect the step-down transformer
3. Protect from open circuits
4. Prevent single-phasing of the motor
19. The technician should use a _____ to cut a keyway in a shaft.
1. Milling machine
2. Lathe
3. Jig gritter
4. Surface Grinder
