1|Page
Certified Fiber Optics Final Exam, fiber optics final
test, fiber installation and testing, optical fiber
certification, fiber troubleshooting, verified answers,
fiber optics technician exam
A fiber optic installer must follow ____,____ and local building
codes when installing fiber optic cables. - ANSWER-Federal,
State
A Fiber optic installer should allow for extra ____ when
installing a cable to allow for future changes or restorations in
the network design. - ANSWER-Slack
________ plant cables are permitted to be installed in the
building as long as the cable dose not exceed 15m(50 ft) -
ANSWER-Outside
Multimode fiber optic systems typically operate at____ and
____ using a _____ source - ANSWER-LED
,2|Page
single mode fiber optic systems typically operate at ______ and
______ source - ANSWER-850-1310, 1300-1550, LED Laser
(LAN's) typically used _______ sources and Wide Area
Networks typically used________sources - ANSWER-LED,
Laser
The newest laser optimized multimode optical fiber Is designed
for 1 Gigabit per second or greater data rates in communication
system utilizing an___ nm vertically cavity surface-emitting
laser(VCSEL) - ANSWER-850
The spectral width of an LED is _____ spectral width of a laser -
ANSWER-Wider
a Laser has a____ output then an LED - ANSWER-Higher
stimulated emission is the process where each photon has the
same ___, phase relationship, and ____ as the first photon -
ANSWER-wavelength , Direction
Fiber optic receivers typically use a _____to detect light -
ANSWER-Photodiode
, 3|Page
the tensile load rating or tension specification specifies the
______ of the fiber optic cable. - ANSWER-Strength
A____ is convenient way to rearrange fiber connections and
circuits - ANSWER-Patch Panal
A feature not normally found in organizers, distribution, or cable
management products in specifying ______type - ANSWER-
Fiber
Fiber optic cable splices are protected in a splice _____ designed
for use in the outdoor environment. - ANSWER-closure
The tensile loading allowed during installation is ____than that
allowed after installation. - ANSWER-higher
pulling tapes should always be attached to the - ANSWER-
strength Members
Certified Fiber Optics Final Exam, fiber optics final
test, fiber installation and testing, optical fiber
certification, fiber troubleshooting, verified answers,
fiber optics technician exam
A fiber optic installer must follow ____,____ and local building
codes when installing fiber optic cables. - ANSWER-Federal,
State
A Fiber optic installer should allow for extra ____ when
installing a cable to allow for future changes or restorations in
the network design. - ANSWER-Slack
________ plant cables are permitted to be installed in the
building as long as the cable dose not exceed 15m(50 ft) -
ANSWER-Outside
Multimode fiber optic systems typically operate at____ and
____ using a _____ source - ANSWER-LED
,2|Page
single mode fiber optic systems typically operate at ______ and
______ source - ANSWER-850-1310, 1300-1550, LED Laser
(LAN's) typically used _______ sources and Wide Area
Networks typically used________sources - ANSWER-LED,
Laser
The newest laser optimized multimode optical fiber Is designed
for 1 Gigabit per second or greater data rates in communication
system utilizing an___ nm vertically cavity surface-emitting
laser(VCSEL) - ANSWER-850
The spectral width of an LED is _____ spectral width of a laser -
ANSWER-Wider
a Laser has a____ output then an LED - ANSWER-Higher
stimulated emission is the process where each photon has the
same ___, phase relationship, and ____ as the first photon -
ANSWER-wavelength , Direction
Fiber optic receivers typically use a _____to detect light -
ANSWER-Photodiode
, 3|Page
the tensile load rating or tension specification specifies the
______ of the fiber optic cable. - ANSWER-Strength
A____ is convenient way to rearrange fiber connections and
circuits - ANSWER-Patch Panal
A feature not normally found in organizers, distribution, or cable
management products in specifying ______type - ANSWER-
Fiber
Fiber optic cable splices are protected in a splice _____ designed
for use in the outdoor environment. - ANSWER-closure
The tensile loading allowed during installation is ____than that
allowed after installation. - ANSWER-higher
pulling tapes should always be attached to the - ANSWER-
strength Members
