Page | 1
ADVANCE RIGGER TEST 2025 BRAND
NEW ACTUAL EXAM WITH ANSWERS.
1. Which of the following items are used for heavy rigging?
a. Rope and chain link
b. Slings, shackles, and spreader beam
c. Chain, rope, bolts, and nuts
d. Lifting eye and rope - correct answer -b. Slings, shackles,
and spreader beam
2. If the jacket of a synthetic round sling is damaged, that sling
should be:
a. Used until further damage occurs
b. De-rated to 50% of its rated capacity
c. Removed from service immediately
d. Duct taped to prevent further damage - correct answer -c.
Removed from service immediately
3. Which of the following is NOT a factor when making
submerged lifts?
a. Ground stability
b. Wave action
c. Buoyancy
d. Water temperature - correct answer -d. Water temperature
, Page | 2
4. When a tugger is mounted where the operator can NOT see
the load, the signal person MUST use:
a. Tugger type signals
b. Overhead crane signals
c. Aggressive signals
d. Signals used for cranes - correct answer -d. Signals used
for cranes
5. Who can design a personnel platform?
a. A qualified personnel
b. The general contractor
c. A site supervisor
d. The rigger - correct answer -a. A qualified personnel
6. A one-inch, 3-leg bridle wire rope sling, rigged at a 45° angle, is
good for 18 tons. The addition of a fourth leg will increase your
capacity by:
a. 0 lbs
b. 6,000 lbs
c. 16,000 lbs
d. 18,000 lbs - correct answer -a. 0 lbs
, Page | 3
7. After any structural repair or modification, a personnel lifting
platform shall be tested to what percentage of the platform
rating?
a. 100%
b. 125%
c. 150%
d. 200% - correct answer -c. 150%
8. All of the following statements about crane contact with power
lines are TRUE EXCEPT:
a. The operator must assume lines are energized
b. The operator should leave the cab as quickly as possible
c. The operator should try to reverse the movement of the cab
to disentangle from the power lines
d. If jumping is necessary, the operator should land with both
feet together - correct answer -b. The operator should leave
the cab as quickly as possible
9. Loads introduced into the machine or its components due to
accelerating or decelerating force is called:
a. Running loading
b. Cross point loading
c. Dynamic loading
d. Un-stabilized loading - correct answer -c. Dynamic loading
ADVANCE RIGGER TEST 2025 BRAND
NEW ACTUAL EXAM WITH ANSWERS.
1. Which of the following items are used for heavy rigging?
a. Rope and chain link
b. Slings, shackles, and spreader beam
c. Chain, rope, bolts, and nuts
d. Lifting eye and rope - correct answer -b. Slings, shackles,
and spreader beam
2. If the jacket of a synthetic round sling is damaged, that sling
should be:
a. Used until further damage occurs
b. De-rated to 50% of its rated capacity
c. Removed from service immediately
d. Duct taped to prevent further damage - correct answer -c.
Removed from service immediately
3. Which of the following is NOT a factor when making
submerged lifts?
a. Ground stability
b. Wave action
c. Buoyancy
d. Water temperature - correct answer -d. Water temperature
, Page | 2
4. When a tugger is mounted where the operator can NOT see
the load, the signal person MUST use:
a. Tugger type signals
b. Overhead crane signals
c. Aggressive signals
d. Signals used for cranes - correct answer -d. Signals used
for cranes
5. Who can design a personnel platform?
a. A qualified personnel
b. The general contractor
c. A site supervisor
d. The rigger - correct answer -a. A qualified personnel
6. A one-inch, 3-leg bridle wire rope sling, rigged at a 45° angle, is
good for 18 tons. The addition of a fourth leg will increase your
capacity by:
a. 0 lbs
b. 6,000 lbs
c. 16,000 lbs
d. 18,000 lbs - correct answer -a. 0 lbs
, Page | 3
7. After any structural repair or modification, a personnel lifting
platform shall be tested to what percentage of the platform
rating?
a. 100%
b. 125%
c. 150%
d. 200% - correct answer -c. 150%
8. All of the following statements about crane contact with power
lines are TRUE EXCEPT:
a. The operator must assume lines are energized
b. The operator should leave the cab as quickly as possible
c. The operator should try to reverse the movement of the cab
to disentangle from the power lines
d. If jumping is necessary, the operator should land with both
feet together - correct answer -b. The operator should leave
the cab as quickly as possible
9. Loads introduced into the machine or its components due to
accelerating or decelerating force is called:
a. Running loading
b. Cross point loading
c. Dynamic loading
d. Un-stabilized loading - correct answer -c. Dynamic loading
