Amt 2 Study Guide Latest Updated 2025/2026 Exam With Complete Questions And Sure Verified Solutions 100% Graded At A+ Score Sure Guaranteed Pass!!

AMT 2 study guide LATEST UPDATED 2025/2026 exam WITH COMPLETE QUESTIONS AND SURE VERIFIED SOLUTIONS 100% GRADED AT A+ SCORE SURE GUARANTEED PASS!! 1. Amtrak Conductors and Engineer are classified as class ______ employees - ANSWER C. [1.103] 2. Conductive material such as steel tape measure, wire, wet or nonrated rope, or linen tape-line containing metallic reinforcement can be used around energized wire, apparatus, equipment, or third rail. True or False? - ANSWER False. [1.114] 3. The Minimum Approach Distance for AMT-2 Qualified Employees whether or not protected by Class A employee against Transmission Wires energized or de-energized and not grounded is? - ANSWER 8ft. [Table 1] 4. What is the Minimum Approach Distance for AMT-2 Qualified Employee whether or not protected by a Class A employee against the Catenary, Signal Line, and Utility Wires less than 35000 volts, energized or de-energized and not grounded? - ANSWER 3ft. [Table 1] 5. Should employees in electrified territory be familiar with the location and operation of radios and telephones? - ANSWER Yes [1.204] 6. When using railroad telephone lines or radios, and you hear the word "EMERGENCY" repeated three times, what must be done? - ANSWER All others using the phone line or radio channel must yield immediately. [1.205] 7. All occurrences or conditions which are likely to affect electric Operations must be reported immediately to whom? - ANSWER The Power Director/Train Dispatcher. [1.201] 8. Minimum Approach Distance means? - ANSWER The distance that must be maintained between personnel and or equipment and all exposed energized lines. Minimum Approach Distance is measured between the person or the end of a tool, equipment, or material being used and the exposed energized parts. [1.301] 9. All overhead wires must be considered energized (Live) at all times except? - ANSWER When it is known to be de-energized, tested de-energized and grounded. [1.302] 10. The third rail must be considered energized (live) at all times except? - ANSWER When it is known to be de-energized, tested de-energized and a Third Rail Warning Device is applied. [1.303] 11. Electric engines and Multiple Units (MU) under overhead wires must be considered energized (Live) except? - ANSWER When it is known that all Pantographs are down and Pantograph grounding switches are closed, or overhead wires are de-energized, tested de-energized and properly grounded. [1.501] 12. Can employees touch or remove unidentified dangling wires, trees, or foreign objects in contact with overhead wires or third rail? - ANSWER NO ,employees must take necessary precautions to protect others and equipment and maintain Minimum Approach Distance . [1.206] 13. What is the Minimum Approach Distance for AMT-2 Qualified Employees against Transmission Wires for equipment operating in the vicinity of wires energized or de-energized and not grounded? - ANSWER 15ft. [Table 1] 14. The Minimum Approach Distance for AMT-2 Qualified Employees against Catenary, Signal Line, Utility Wires Less than 35000 volts for Equipment operating in the vicinity of wires energized or de-energized and not grounded is/ - ANSWER 3ft. [Table 1] 15. Personnel and Equipment being provided protection by Class A Employee, wires de-energized, tested de-energized, and grounded will be allowed? - ANSWER Full Contact. [Table 1] 16. The Minimum Approach Distance for Unidentified Dangling Wires is? - ANSWER 15ft. [Table 1] 17. What is the Minimum Approach Distance while walking over and around energized Third Rail? - ANSWER 6 inches. [Table 2] 18. what is the Minimum Approach Distance for AMT-2 Qualified Employees working with conductive tools or