UST TEST PREP QUESTIONS |
REVISION MATERIALS 2025|26 |
GUARANTEED ACCURATE
ANSWERS |VERIFIED |LATEST
VERSION
What is the maximum pressure to be placed on a FRP tank during a pre-
installation test?
A. 3 pounds
B. 10 pounds
C. 50 pounds
D. 15 pounds - ACCURATE ANSWERS✔✔ A. 3 pounds
In absence of local requirements, the recommended minimum distance
between a tank excavation and adjacent structures or property lines?
A. 10 feet.
B. 50 feet
C. 2 feet
D. 5 feet - ACCURATE ANSWERS✔✔ D. 5 feet
According to FRP tank manufactures' specifications, the burial depth for
an FRP tank should not exceed?
,A. 2 feet
B. 12 feet
C. 7 feet
D. 4 feet - ACCURATE ANSWERS✔✔ C. 7 feet
Industry codes, as well as the specification of individual manufactures,
do not entirely agree as to the minimum space that should be maintained
between tanks in stable soil conditions. Listed below are ranges of
minimum spacing between tanks, derived from various industry codes
and manufactures specifications. which range is most accurate?
A. From 30 to 40 inches.
B. From 12 to 24 inches.
C. From 6 to 10 inches.
D. From 36 to 48 inches. - ACCURATE ANSWERS✔✔ B. From 12 to
24 inches.
When installing a steel tank which has zinc anodes welded directly onto
the tank for cathodic protection, you should?
A. Take care not to touch the anodes, in order to avoid danger of
electrical shock.
B. Securely wrap the anodes in plastic, so they will remain dry after
installation, regardless of depth of the water table.
C. Connect each of the anodes to all others with an insulated wire.
EXAMLINKS
STUDY SMART,
, D. Remove the plastic wrappings around the anodes prior to installation.
- ACCURATE ANSWERS✔✔ D. Remove the plastic wrappings around
the anodes prior to installation.
If local authorities and tank manufactures permit a sand slurry mixture
to be used for backfilling a tank, what steps should be taken to insure
that use of the slurry is proper?
A. Use only personnel trained in the sand slurry method by the tank
manufacturer, and use the method only with the manufacturer's prior
approval.
B. Combine the sand slurry mixture with two parts of crushed stone.
C. Use salt water in preparing the slurry mixture.
D. Pump the slurry mixture into the excavation through a 1/2 inch hose.
- ACCURATE ANSWERS✔✔ A. Use only personnel trained in the sand
slurry method by the tank manufacturer, and use the method only with
the manufacturer's prior approval.
What is the minimum depth of bedding required for a pipe trench in
traffic areas?
A. 12 inches.
B. 6 inches.
C. 2 inches.
D. 18 inches. - ACCURATE ANSWERS✔✔ B. 6 inches.
EXAMLINKS
STUDY SMART,
REVISION MATERIALS 2025|26 |
GUARANTEED ACCURATE
ANSWERS |VERIFIED |LATEST
VERSION
What is the maximum pressure to be placed on a FRP tank during a pre-
installation test?
A. 3 pounds
B. 10 pounds
C. 50 pounds
D. 15 pounds - ACCURATE ANSWERS✔✔ A. 3 pounds
In absence of local requirements, the recommended minimum distance
between a tank excavation and adjacent structures or property lines?
A. 10 feet.
B. 50 feet
C. 2 feet
D. 5 feet - ACCURATE ANSWERS✔✔ D. 5 feet
According to FRP tank manufactures' specifications, the burial depth for
an FRP tank should not exceed?
,A. 2 feet
B. 12 feet
C. 7 feet
D. 4 feet - ACCURATE ANSWERS✔✔ C. 7 feet
Industry codes, as well as the specification of individual manufactures,
do not entirely agree as to the minimum space that should be maintained
between tanks in stable soil conditions. Listed below are ranges of
minimum spacing between tanks, derived from various industry codes
and manufactures specifications. which range is most accurate?
A. From 30 to 40 inches.
B. From 12 to 24 inches.
C. From 6 to 10 inches.
D. From 36 to 48 inches. - ACCURATE ANSWERS✔✔ B. From 12 to
24 inches.
When installing a steel tank which has zinc anodes welded directly onto
the tank for cathodic protection, you should?
A. Take care not to touch the anodes, in order to avoid danger of
electrical shock.
B. Securely wrap the anodes in plastic, so they will remain dry after
installation, regardless of depth of the water table.
C. Connect each of the anodes to all others with an insulated wire.
EXAMLINKS
STUDY SMART,
, D. Remove the plastic wrappings around the anodes prior to installation.
- ACCURATE ANSWERS✔✔ D. Remove the plastic wrappings around
the anodes prior to installation.
If local authorities and tank manufactures permit a sand slurry mixture
to be used for backfilling a tank, what steps should be taken to insure
that use of the slurry is proper?
A. Use only personnel trained in the sand slurry method by the tank
manufacturer, and use the method only with the manufacturer's prior
approval.
B. Combine the sand slurry mixture with two parts of crushed stone.
C. Use salt water in preparing the slurry mixture.
D. Pump the slurry mixture into the excavation through a 1/2 inch hose.
- ACCURATE ANSWERS✔✔ A. Use only personnel trained in the sand
slurry method by the tank manufacturer, and use the method only with
the manufacturer's prior approval.
What is the minimum depth of bedding required for a pipe trench in
traffic areas?
A. 12 inches.
B. 6 inches.
C. 2 inches.
D. 18 inches. - ACCURATE ANSWERS✔✔ B. 6 inches.
EXAMLINKS
STUDY SMART,
