MK1 SWE QUESTIONS AND ANSWERS
When is the cutter engineering report due? - Answers :Jan 31
What type of engine is on a P100 - Answers :Single cylinder air cooled four stroke
How long will a P6 pump run on a tank of fuel - Answers :4 hours
What type of engine is on a P6 pump - Answers :6.5 horsepower Honda GX-200 has
engine
How would you test 4-20 mA sensor - Answers :In series
The MPU - 23 card exhibits what color lights on the panel when operating normally -
Answers :Green Yellow Yellow
How many digits are in a NSN - Answers :13
What cut are R/G teeth? - Answers :helical
Oil fog out of R/G - Answers :Faulty precipitator
Standard hoses shall be identified as Standard in Hose Log and shall be scheduled for
replacement at intervals not to exceed - Answers :8 years
What % hydraulic failure is due to contamination? - Answers :80%
Hoses installed in the weather without an outer covering specifically designed for
service in the weather shall have a service life not to exceed - Answers :5 years
When using an ammeter to troubleshoot a system always use what - Answers :The
highest scale
Small engine exhaust hose service life shall be in accordance with the hose
manufacturer recommendation or - Answers :5 years whichever is less
The most common type of media for coarse filtration is - Answers :Surface media
What is the disadvantage of a centrifugal pump - Answers :Suction lift
The shelf life for hoses and prefabricated hose assemblies shall not exceed - Answers
:10 years
As wire size increases, what happens to resistance and amperage? - Answers
:Resistance down - Amperage up
,What does CAN stand for? - Answers :Controller Area Network
What % of working pressure do you test a temp hose - Answers :150
How does a rise in the R/O input water temp effect the output temp - Answers :Output
increases
What coolant is used in a keel cooler? - Answers :antifreeze
At a modernized unit, where is your boat inspection report recorded? - Answers :ALMIS
How often is the cutter engineering report conducted - Answers :Yearly
Rudder stock is supported by what? - Answers :bearing
Waster ring in the sea chest is for what? - Answers :prevent galvanic corrosion
What is the acceptable leakage rate in a screw type hydraulic pump shaft seal -
Answers :50ml
If you have a bearing failure in a centrifugal pump with excessive vibration, what is the
likely cause? - Answers :misalignment
What causes aeration in a hydraulic system if there are no leaks? - Answers :low fluid
You find something else is wrong with a piece of equipment already CASREPed what
should you send? - Answers :Update
A thrust bearing supports what type of movement - Answers :axial and radial
What does SSS stand for in a SSS clutch? - Answers :Syncro-Self-Shifting
How is tin measured in a spectrometric oil analysis? - Answers :ppm
If you find 40psi in a TANB trailer tire what type of discrepancy is it? - Answers
:restrictive
Where can DEMPS procedures be found? - Answers :NEM-233-11
What type of fuel does a P100 run on - Answers :F76 and JP5
When do you have zincs in freshwater - Answers :Never
What is considered a hot surface on piping requiring flange shielding for LO - Answers
:650
,What is considered a hot surface on piping requiring flange shielding for FO - Answers
:400
What happens to hydraulic oil for every 18 degrees it rises above 140 - Answers
:Oxidation rate doubles
What type of o-ring is the most resistant to petroleum products - Answers :Buna-S
Before you inflate a shaft seal what must you do first - Answers :Stop and lock shaft
After an oil and filter change how many hours of engine operation should be allowed
before sampling - Answers :25 hours
Check amps on a non clamp ammeter - Answers :In series
How is the boat record kept in a modernized unit - Answers :EAL
What is the max thickening and dilution of L/O - Answers :40% thickening, 5% dilution
Oil intervals on a R/G - Answers :500 hours
what should the chlorine levels on the potable water shore tie be - Answers :.02ppm for
15min or .02ppm for 30min
What date is placed on the hose tag - Answers :Replacement
Jacket water is tested - Answers :monthly
What type of fuel has FSII - Answers :F44
what size safety chains are used on an rbs trailer - Answers :1/2"
What PMS does not show up in the Cutter engineering report - Answers :Daily and
weekly
Wet and dry bulb thermometer determines - Answers :Humidity
What is the PSI for a medium service air system - Answers :151 to 1000 psi
Engineering casualty control is concerned with - Answers :Prevention minimization and
correction of operational and battle casualties
Excessive property should be reported to - Answers :Property officer
Which component can be pressure compensated or non pressured - Answers :Flow
control valve
, If a CAN buss has 120 ohm resistors at each end what is the total resistance on the
good CAN buss? - Answers :60 ohms
What do you clean a battery terminal with - Answers :Sodium Bicarbonate/ Ammonia
Where do you place a plastigauge - Answers :Center
What are the 4 parts of a turbine - Answers :Compressor, Combustor, Turbine, Auxiliary
What is the flashpoint of F-76? - Answers :140°
Smallest particle visible to the naked eye - Answers :40 microns
What will take hierarchy if manuals conflict - Answers :NEM
Max leakage rate on a screw type pump - Answers :50 ml
When building an o ring what is the max stretch for inside diameter - Answers :No more
than 10%
What is 1/8 as a decimal? - Answers :0.125
While test running BF225 Honda what is the Minimum voltage - Answers :12 volts
On a TANB Trailer, Tire Pressure below 40PSI - Answers :Restrictive discrepancy
On a TANB trailer tire tread depth below 1/8" - Answers :Restrictive discrepancy
When do you adjust the gap on an iridium spark plug - Answers :Never
How long do you have to reset the DTC with the jumper installed (Honda) - Answers :20
seconds
What RPM does VTECH engage on a BF150 - Answers :4300 RPM
At what RPM does the VTEC Activate on a BF-225 - Answers :4500rpm
When low oil pressure is detected in a Honda what does it do - Answers :Returns to idle
What tells you the a boat is safe to run in Almis - Answers :Fully Mission Capable
what is a clear and bright test? - Answers :Looking for water and sediment
When you increase wire diameter what happen - Answers :Decrease resistance and
increase flow
When is the cutter engineering report due? - Answers :Jan 31
What type of engine is on a P100 - Answers :Single cylinder air cooled four stroke
How long will a P6 pump run on a tank of fuel - Answers :4 hours
What type of engine is on a P6 pump - Answers :6.5 horsepower Honda GX-200 has
engine
How would you test 4-20 mA sensor - Answers :In series
The MPU - 23 card exhibits what color lights on the panel when operating normally -
Answers :Green Yellow Yellow
How many digits are in a NSN - Answers :13
What cut are R/G teeth? - Answers :helical
Oil fog out of R/G - Answers :Faulty precipitator
Standard hoses shall be identified as Standard in Hose Log and shall be scheduled for
replacement at intervals not to exceed - Answers :8 years
What % hydraulic failure is due to contamination? - Answers :80%
Hoses installed in the weather without an outer covering specifically designed for
service in the weather shall have a service life not to exceed - Answers :5 years
When using an ammeter to troubleshoot a system always use what - Answers :The
highest scale
Small engine exhaust hose service life shall be in accordance with the hose
manufacturer recommendation or - Answers :5 years whichever is less
The most common type of media for coarse filtration is - Answers :Surface media
What is the disadvantage of a centrifugal pump - Answers :Suction lift
The shelf life for hoses and prefabricated hose assemblies shall not exceed - Answers
:10 years
As wire size increases, what happens to resistance and amperage? - Answers
:Resistance down - Amperage up
,What does CAN stand for? - Answers :Controller Area Network
What % of working pressure do you test a temp hose - Answers :150
How does a rise in the R/O input water temp effect the output temp - Answers :Output
increases
What coolant is used in a keel cooler? - Answers :antifreeze
At a modernized unit, where is your boat inspection report recorded? - Answers :ALMIS
How often is the cutter engineering report conducted - Answers :Yearly
Rudder stock is supported by what? - Answers :bearing
Waster ring in the sea chest is for what? - Answers :prevent galvanic corrosion
What is the acceptable leakage rate in a screw type hydraulic pump shaft seal -
Answers :50ml
If you have a bearing failure in a centrifugal pump with excessive vibration, what is the
likely cause? - Answers :misalignment
What causes aeration in a hydraulic system if there are no leaks? - Answers :low fluid
You find something else is wrong with a piece of equipment already CASREPed what
should you send? - Answers :Update
A thrust bearing supports what type of movement - Answers :axial and radial
What does SSS stand for in a SSS clutch? - Answers :Syncro-Self-Shifting
How is tin measured in a spectrometric oil analysis? - Answers :ppm
If you find 40psi in a TANB trailer tire what type of discrepancy is it? - Answers
:restrictive
Where can DEMPS procedures be found? - Answers :NEM-233-11
What type of fuel does a P100 run on - Answers :F76 and JP5
When do you have zincs in freshwater - Answers :Never
What is considered a hot surface on piping requiring flange shielding for LO - Answers
:650
,What is considered a hot surface on piping requiring flange shielding for FO - Answers
:400
What happens to hydraulic oil for every 18 degrees it rises above 140 - Answers
:Oxidation rate doubles
What type of o-ring is the most resistant to petroleum products - Answers :Buna-S
Before you inflate a shaft seal what must you do first - Answers :Stop and lock shaft
After an oil and filter change how many hours of engine operation should be allowed
before sampling - Answers :25 hours
Check amps on a non clamp ammeter - Answers :In series
How is the boat record kept in a modernized unit - Answers :EAL
What is the max thickening and dilution of L/O - Answers :40% thickening, 5% dilution
Oil intervals on a R/G - Answers :500 hours
what should the chlorine levels on the potable water shore tie be - Answers :.02ppm for
15min or .02ppm for 30min
What date is placed on the hose tag - Answers :Replacement
Jacket water is tested - Answers :monthly
What type of fuel has FSII - Answers :F44
what size safety chains are used on an rbs trailer - Answers :1/2"
What PMS does not show up in the Cutter engineering report - Answers :Daily and
weekly
Wet and dry bulb thermometer determines - Answers :Humidity
What is the PSI for a medium service air system - Answers :151 to 1000 psi
Engineering casualty control is concerned with - Answers :Prevention minimization and
correction of operational and battle casualties
Excessive property should be reported to - Answers :Property officer
Which component can be pressure compensated or non pressured - Answers :Flow
control valve
, If a CAN buss has 120 ohm resistors at each end what is the total resistance on the
good CAN buss? - Answers :60 ohms
What do you clean a battery terminal with - Answers :Sodium Bicarbonate/ Ammonia
Where do you place a plastigauge - Answers :Center
What are the 4 parts of a turbine - Answers :Compressor, Combustor, Turbine, Auxiliary
What is the flashpoint of F-76? - Answers :140°
Smallest particle visible to the naked eye - Answers :40 microns
What will take hierarchy if manuals conflict - Answers :NEM
Max leakage rate on a screw type pump - Answers :50 ml
When building an o ring what is the max stretch for inside diameter - Answers :No more
than 10%
What is 1/8 as a decimal? - Answers :0.125
While test running BF225 Honda what is the Minimum voltage - Answers :12 volts
On a TANB Trailer, Tire Pressure below 40PSI - Answers :Restrictive discrepancy
On a TANB trailer tire tread depth below 1/8" - Answers :Restrictive discrepancy
When do you adjust the gap on an iridium spark plug - Answers :Never
How long do you have to reset the DTC with the jumper installed (Honda) - Answers :20
seconds
What RPM does VTECH engage on a BF150 - Answers :4300 RPM
At what RPM does the VTEC Activate on a BF-225 - Answers :4500rpm
When low oil pressure is detected in a Honda what does it do - Answers :Returns to idle
What tells you the a boat is safe to run in Almis - Answers :Fully Mission Capable
what is a clear and bright test? - Answers :Looking for water and sediment
When you increase wire diameter what happen - Answers :Decrease resistance and
increase flow
