SHP Smart Home Pro Final UPDATED
Exam Questions and CORRECT Answers
The firefighter may be installed next to a stand-alone battery smoke detector - CORRECT
ANSWER - True
When performing a full system test, you may bypass any open doors or windows - CORRECT
ANSWER - False
When programming an skey1,you must - CORRECT ANSWER - Always enable the
emergency
When running power to the take345,polarity doesn't apply - CORRECT ANSWER - False
When programming the emergency key for the skey1,which zone/sensor type is used. -
CORRECT ANSWER - Audible alarm (7)
When installing a smkt3,you must use the included screws and anchors - CORRECT
ANSWER - True
When installing the firefighter, it is required to test the customers existing smoke detectors -
CORRECT ANSWER - True
When installing a Dw21, where is the approved location for the sensor - CORRECT
ANSWER - Between 6"(15cm) and 2'(61cm) from floor
When installing a dw11 on a vinyl or metal frame, what should primarily use to mount the sensor
- CORRECT ANSWER - Provided double sided tape
, Which of the following materials can you use to group multiple ground terminals in a takeover. -
CORRECT ANSWER - Beans & wire caps
Which of the following sensors are you not allowed to program using a translator - CORRECT
ANSWER - Smoke detector
When installing the take345, you must always test the new 12v battery before using it. -
CORRECT ANSWER - True
What is the output voltage of transformer used to power the sky control - CORRECT
ANSWER - 16.5
What is the minimum distance for placement of a co3 from the corners of the wall - CORRECT
ANSWER - 12"
The smkt3 has 2 function:smoke and heat detection - CORRECT ANSWER - False
How would you program a co3 if mounted on a hallway wall - CORRECT ANSWER - Loop
1 Zone 14
When installing a translator, you must program all of the existing sensors as new equipment on
the panel - CORRECT ANSWER - False
The dw21 should always be installed in the door frame - CORRECT ANSWER - True
Which of the following zone/sensor types are correct when programming an smkt3 - CORRECT
ANSWER - (09) Smoke detector. (09) Heat detector. (08) Freeze
What it the correct height ar which to install the Pir2 - CORRECT ANSWER - 7ft
Exam Questions and CORRECT Answers
The firefighter may be installed next to a stand-alone battery smoke detector - CORRECT
ANSWER - True
When performing a full system test, you may bypass any open doors or windows - CORRECT
ANSWER - False
When programming an skey1,you must - CORRECT ANSWER - Always enable the
emergency
When running power to the take345,polarity doesn't apply - CORRECT ANSWER - False
When programming the emergency key for the skey1,which zone/sensor type is used. -
CORRECT ANSWER - Audible alarm (7)
When installing a smkt3,you must use the included screws and anchors - CORRECT
ANSWER - True
When installing the firefighter, it is required to test the customers existing smoke detectors -
CORRECT ANSWER - True
When installing a Dw21, where is the approved location for the sensor - CORRECT
ANSWER - Between 6"(15cm) and 2'(61cm) from floor
When installing a dw11 on a vinyl or metal frame, what should primarily use to mount the sensor
- CORRECT ANSWER - Provided double sided tape
, Which of the following materials can you use to group multiple ground terminals in a takeover. -
CORRECT ANSWER - Beans & wire caps
Which of the following sensors are you not allowed to program using a translator - CORRECT
ANSWER - Smoke detector
When installing the take345, you must always test the new 12v battery before using it. -
CORRECT ANSWER - True
What is the output voltage of transformer used to power the sky control - CORRECT
ANSWER - 16.5
What is the minimum distance for placement of a co3 from the corners of the wall - CORRECT
ANSWER - 12"
The smkt3 has 2 function:smoke and heat detection - CORRECT ANSWER - False
How would you program a co3 if mounted on a hallway wall - CORRECT ANSWER - Loop
1 Zone 14
When installing a translator, you must program all of the existing sensors as new equipment on
the panel - CORRECT ANSWER - False
The dw21 should always be installed in the door frame - CORRECT ANSWER - True
Which of the following zone/sensor types are correct when programming an smkt3 - CORRECT
ANSWER - (09) Smoke detector. (09) Heat detector. (08) Freeze
What it the correct height ar which to install the Pir2 - CORRECT ANSWER - 7ft
